Clevo M76xSU Download Drivers und Manual

Realtek 8169/8168/8101 PCI/PCIe NDIS6 driver (for Windows Vista)
------------------------------------------------

Version 6.197.0917.2007

1. Open LargeSend Offload Version 2 options

Largesend Offload version 2 supports both Ipv4 and Ipv6

DO NOT CHANGE THOSE SETTINGS for 8111C

Large Send Offload (IPv4) = Enabled
Large Send Offload v2 (IPv4) = Disabled
Large Send Offload v2 (IPv6) = Enabled

2. Enable Receiving-Side Scaling (default setting)

3. OID_GEN_VENDOR_DESCRIPTION has more detail description for various NIC

Some ethernet packets capture tool need this OID to have detail description

4. Support BaseCpuNumber for RSS (8111C)

Thus, quad-core CPU could use RSS now.

2 cores, 4 cores, 8 cores, 16 cores and 32 cores all support RSS.

Previous version only enable RSS when running on a dual-core machine.

5. Add reset mechanism for BIOS PCI-reset (8111C, 8102E)

This is for overclock. 8102E is not supported by this verision.

6. New PHY parameter (8111C)

Advanced link down power saving
------------------------------------------------

Version 6.196.0803.2007

For 8168C users, please update to this version.

1. New powersaving feature

Lowest link speed when sleep or shutdown

This feature only valid when speed and duplex is auto-neg

If link partner support 10 Mbps : 10 half / 10 full NWAY
If link partner does not support 10 Mbps : 10 half / 10 full / 100 half / 100 full NWAY

2. Remove option - Sleep WOL Power Saving

3. Add VistaCDM diagnostic routine for register read/write test

4. Fix driver bug : performance test tool may stop to test
------------------------------------------------

Version 6.195.0625.2007

1. Improve copy file speed on the platform with very slow CPU

2. Fix PHY speed changed bug: Force to 10Mbps but S3/S4 change to 100Mbps.

This is because driver change to 10/100 auto neg mode when S3/S4.

3. Fix incorrect WOL behavior on a specific notebook (S3 enabled but S4 disabled)

4. Add VistaPE diagnostic routine to check interrupt.

Synaptics Pointing Device Driver Release Notes
Version 10.0.12
----------------------------------------------------------------------------
Overview
----------------------------------------------------------------------------
This document describes changes to the Synaptics TouchPad Driver
for Windows 9x & ME, Windows NT, Windows 2000, Windows XP and Vista.
Only external releases have been documented.
Other releases were for internal use, beta tests, or for specific
customer requests. These are not documented here.
----------------------------------------------------------------------------
Version 10.0.12 08/17/2007 (Win2K/WinXP/Vista)
----------------------------------------------------------------------------
Bug Fixes
-Fixed the parameter in SetCurrentDevice to be the device index, not the
device handle.
-Applied NavPoint features for OEM Pnp ID SYN0B0E.
-Check if Vista ahead of send WM_APP message.
-Changed to use WM_APP instead of WM_USER message.
-Chenged to use a different WM_APP message for mouse control.
-Removed a device (could be a real mouse) from the Pnp exclusion list.
-Added SYN0301 to an OEM customers INF file.
-Added an empty string check before we attempt to convert the path resource
ID to an integer for OSD settings. If the string is empty, we skip and
retrieve the next token.
-Changed 2 other implementations of the tokenize function to check for
empty strings.
-Fixed a bug where in Vista x64 SynTPStart could not bring up the
Enhancments application (SyntpEnh.exe).
-Added basic On Screen Button click code for OSD. At this stage we can
determine which object we have clicked on, but no action is being
performed yet.
-Added a new Pnp ID SYN1911 for an OEM customer.
-Added the "Disable internal pointing device when external USB pointing
device is attached" feature to the settings for OEM Pnp ID SYN0A0D.
-Added a new Pnp ID SYN014C for an OEM customer.
----------------------------------------------------------------------------
Version 10.0.11 08/10/2007 (Win2K/WinXP/Vista)
----------------------------------------------------------------------------
Bug Fixes
-Merged OSD branch into trunk.
-Fixed garbage characters in SynDiag LOG file in registry info.
-Fixed SynDiag log file in Japanese OS so it no longer gets garbage
chararacters for KTL log section.
-Added OEM PNP ID as per OEM request.
-Added USB touch panel devices to the exclusion list.
-Fixed a bug where we were sometimes unable to collect the daignostic
log file in Vista.
-Added OEM PNP ID as per OEM request.
-Added a new PnPID for an OEM customer.
-Add SYN1601 to an OEM customers INF file.
-Added a new USB HID to the exclusion list for an OEM customer.
-Added PNPID SYN0D05 to an OEM customers INF file.
-Fixed a bug in DoMouseActivate to get correct parameters.
-Added an OEM data file change and re-WHQL request.
-Added code to allow KBC disable feature to override API disable feature.
-Removed USB from NavPoint INF file settings.

This document contains the following sections:

1. System Requirements
3. Installing the Software
4. Verifying Installation of the Software
5. Identifying the Software Version Number
6. Uninstalling the Software
7. Installation Switches Available

SYSTEM REQUIREMENTS
*******************

1. The system must contain one of the following Intel
Chipsets:

Intel(R) Poulsbo Chipset

2. The software should be installed on systems with at
least 512 MB of system memory.

3. There should be sufficient hard disk space in the
<TEMP> directory on the system in order to install
this software.

The drivers included with this distribution package are
designed to function with all releases of Microsoft
Windows* Vista.

INSTALLING THE SOFTWARE
*******************

General Installation Notes:

1. The operating system must be installed prior to the
installation of the driver.
2. This installation procedure is specific only to the
version of driver and installation file included in
this release.
3. This procedure assumes that all of the software
associated with this release is located in the same
directory.

Alps Pointing-device Driver provides a convenient way to modify
setting for Alps Pointing-device. The Alps Pointing-device Driver
is compatible with most standard mice and similar pointing devices.
____________________________________________________________

CONTENTS:

1. Driver Installation for Windows 2000/XP
2. Using the Alps Pointing-device Property Sheets
3. Files On the Setup Disk
____________________________________________________________

1. Driver Installation for Windows 2000/XP

Use this procedure if you use Windows 2000/XP:
1) From the Start menu, select Settings, Control Panel.
2) Double-click Mouse to open Mouse Properties.
3) Select the Hardware tab, and then click Properties.
4) Select the Driver tab, and then click Change.
5) Click Next.
6) Select Display a list of the known drivers for this
device so that I can choose a specific driver, and
then click Next.
7) Click Have Disk.
8) Click Browse.
9) Choose specific directory name that you have copied
driver files.
10) Click Apfiltr.inf, and then click Open.
11) Click OK.
12) Click Alps Pointing-device, and then click Next.
13) Click Next to copy the driver files to your system.
14) Click Finish.
15) Click Close.
16) Click Yes, then restart PC automatically.

To print README.TXT, open it in Windows Write, Microsoft Word,
or another word processor. Then select the entire document
and format the text in 10-point Courier before printing.

This file (README.TXT) contains:

--------
Contents
--------
1) Quick Start
2) How to verify installation
3) Uninstall procedure
4) Update procedure
5) Country selection
6) Call Progress Sounds
7) Known issues
8) Troubleshooting
9) Disclaimers

How to use this RTLSetup Utility
---------------------------------
For Windows ME:

1. If the Operating System's New Hardware Wizard prompts you that
"New Hardware Found" for the "PCI Ethernet Controller", you should
click "Next" until "Finish" is clicked and without specifying
location of the driver. You will see the "PCI Ethernet Controller"
in the Device Manager.

2. Then you can install or update the NDIS driver with "setup" or
"setup -s" command:
a) setup: The InstallShield will prompt you the steps to install
or upgrade the driver.

b) setup -s: The InstallShield will complete the installation or
upgrade without prompting you any instruction.

You need to reboot the system immediately after the Install shield
completes the installation/upgrade.

3. Do not click "Cancel" during New Hardware Wizard searches for the
driver.

4. You can remove RTLSetup utility from Add/Remove Program Palette in
Control Panel, the InstallShield will prompt you the steps to remove
the driver. After remove the driver, please restart the system
immediately.

For Windows 2000/XP:

1. If the Operating System's Found New Hardware Wizard prompts you that
"New Hardware Found" for the "Ethernet Controller", you should click
"Next" until "Finish" is clicked and without specifying location of
the driver. You will see the "Ethernet Controller" in the Device
Manager.

2. Then you can install or upgrade the NDIS driver with "setup" or
"setup -s" command:
a) setup: The InstallShield will prompt you the steps to install
or upgrade the driver.

b) setup -s: The InstallShield will complete the installation or
upgrade without prompting you any instruction.

3. You can remove RTLSetup utility from Add/Remove Program Palette in
Control Panel, the InstallShield will prompt you the steps to remove
the driver. After remove the driver, please restart the system
immediately if you want your networking to be re-installed.

Avance Logic AC'97 Sound System Software ver: A2.60
Installation and Setup
Driver & Application Installation/Removal Procedure For Avance AC'97 Codec:
=================================================================================

<<< For Win98/Win2000/WinME (WDM driver) >>>

---------------------------------------
Setup Driver/Application at first time:
---------------------------------------

Step 1. Before installing the Avance AC'97 Drivers & Applications, Press the
[Cancel] button if Windows detect the PCI Multimedia Audio device.

Step 2. Insert the "Avance AC'97 Drivers & Applications" CD into the CD-ROM
drive and run the setup.exe program to finish the installation.

Step 3. Click on [Next/OK/Go] to continue the procedure. If the Windows popup
"Digital Signature Not Found" message, press [Yes] to continue the
installation.

Step 4. Finally, select to restart the system and press [Finish] to complete
the installation.

The system will reload the drivers and do some adjustments in the INF
file if so required.

--------------------------
Update Driver/Application:
--------------------------

Step 1. Follow Step 2,3,4 described in [Setup at first time] above to complete
the procedure.

--------------------------
Remove Driver/Application:
--------------------------

Step 1. Go to Start\Settings\Control Panel.

Step 2. Select [Add/Remove Programs] icon.

Step 3. Select "Avance AC'97 Drivers and Applications" and press [Change/Remove]
button.

Step 4. Click on [Next/OK/Go] to finish the uninstallation.

Step 5. At the end of the procedure, select to restart the system and press
[Finish] to complete the uninstallation.
<<< For WinNT 4.0 (NT4 driver) >>>

BisonC07Install-D(0709062200)-V(6.32.710.1b)-S(4BA_YUV)-B(07)-C()-61_Agc6
Date : 2007/09/06/22:00
Versiion : Vista/XP32 : 6.32.710.1
note : Update 32 bit system file.
=======================================================================================================
BisonC07Install-D(0709140144)-V(6.32.710.1c)-S(4BA_YUV)-B(07)-C(Clevo)_CL
Date : 2007/09/14/01:44
Versiion : Vista/XP32(6.32.710.1), Vista/XP64(6.64.710.01)
note : Add 64 bit driver.
Reverse preview image.
Change preview application with snapshot & zoom in/out.
Add OEM.ini.
=======================================================================================================
BisonC07Install-D(0709172232)-V(6.32.710.1d)-S(4BA_YUV)-B(07)-C(Clevo)_CL
Date : 2007/09/17/22:32
Versiion : Vista/XP32(6.32.710.1), Vista/XP64(6.64.710.01)
note : Update OEM.ini for Zoom in/out function.
If you want Zoom in/out function, please set "ZoomIn_Out=yes".
If you don't want Zoom in/out function, please set "ZoomIn_Out=no".
=======================================================================================================
BisonC07Install-D(0710082338)-V(6.96.710.1e)-S(4BA_4AA+07)-C(Clevo)_CL
Date : 2007/10/08/23:38
Versiion : 4BA(2M) : Vista/XP32(6.32.710.1), Vista/XP64(6.64.710.1)
4AA(1.3M) : Vista/XP32(6.32.704.3), Vista/XP64(6.64.704.3)
note : Add 64 bit driver for 4BA+5607.
Add 4AA+5607 32/64 bit driver.

If you want Zoom in/out function, please set "ZoomIn_Out=yes".
If you don't want Zoom in/out function, please set "ZoomIn_Out=no".
=======================================================================================================
BisonC07Install-D(0710100022)-V(6.96.710.1f)-S(4BA_4AA+07)-C(Clevo)_CL
Date : 2007/10/10/00:22
Versiion : 4BA(2M) : Vista/XP32(6.32.710.1), Vista/XP64(6.64.710.1)
4AA(1.3M) : Vista/XP32(6.32.704.3), Vista/XP64(6.64.704.3)
note : Update 32/64 bit driver for 4BA+5607 to fix a/v unsync & quality of preview.
Update application to fix install issue & auto close issue.

OEM.ini with new function : [Preview]
ZoomIn_Out=yes yes : preview application with zoom in/zoom out function.
no : preview application without zoom in/zoom out function.
Close_AP_BeforeSleep=no yes : preview application will auto close before into S3/S4.
no : preview application won't auto close before into S3/S4.
DefaultFormat_YUY2_RGB24=yuy2 yuy2 : preview application will use YUY2 as default format.
rgb24: preview application will use RGB24 as default format.

[PowerSaving]
SelectiveSuspend=yes yes : support selective suspend.
no : not support selective suspend.

=======================================================================================================
BisonC07Install-D(0710112314)-V(6.96.710.1g)-S(4BA_4AA+07)-C(Clevo)_CL
Date : 2007/10/11/23:14
Versiion : 4BA(2M) : Vista/XP32(6.32.710.1), Vista/XP64(6.64.710.1)
4AA(1.3M) : Vista/XP32(6.32.710.1), Vista/XP64(6.64.710.1)
note : update 32/64 bit driver for 4AA+5607 with VID_5986&PID_0200.

These changes were made in the current version:

_______________________________________________
Build 5.8.2.4489
FIX: Very rare problem with 100% CPU utilization after startup
FIX: Registration is not replayed sometimes in Firefox
CHG: Signed Firefox Extension
FIX: Control Center cannot be opened on Vista SP1 when ATOK2007 is used

_______________________________________________
Build 5.8.2.4445
FIX: Typo in Japanese
ADD: PasswordBank: support for Firefox 3.0

_______________________________________________
Build 5.8.2.4367
CHG: Signed driver 118 added (for Vista)
FIX: Typo in Japanese
FIX: Upgrade from PS QL 5.8.1

_______________________________________________
Build 5.8.2.4272
FIX: Vista with SP1 and SSO - on some PC, Single Sign On did nor work corectly

_______________________________________________
Build 5.8.2.4249
FIX: Better visibility of links on Introduction screen
FIX: Vista WMP load file name from single file file safe
CHG: Customization of intro screen
FIX: Implementation of lift-finger prompt after swipe
FIX: Different quotation marks (chinese only)
CHG: New biometric library 3.6.1.0035
FIX: User settings changes are not accepted when the User settings dialog is cancelled.
_______________________________________________
Build 5.8.2.4156
ADD: Localization: Full language set added
FIX: Notification: Fix for 'bad image' appearing for ghost swipes on ess2.1 sensor
FIX: Tutorial: Video failed to replay after click back-next after its replay

_______________________________________________
Build 5.8.2.4082
CHG: Signed driver 111 added
FIX: password Bank: Bubble manager endless bubbles
CHG: Added TFM lib 3.6.1.0030 with sonly antispoofing support
FIX: Pasword Bank: memory leaks fixes
CHG: Enrollment: When enrollment operation determines duplicate, it sends only feedback instead of invoking messagebox.

English, French, German, Italian and Spanish