Clevo M810L Download Drivers und Manual

Driver Installation/Removal Procedure For Realtek High Definition Audio Codec:
=================================================================================
<<< For Windows 2000/XP/Vista/Windows7 x86/x64 Driver >>>
---------------------------------------
Setup Driver at first time:
---------------------------------------
Windows 2000 , XP :
Step 1. Before installing the Realtek High Definition Audio Driver, Press the
[Cancel] button if Windows detect the Multimedia Audio device.

Step 2. Run the setup.exe program to start the installation.

Step 3. Click on [Next] to continue the procedure. If the Windows popup
"Digital Signature Not Found" message, press [Yes] to continue the
installation.

Step 4. Finally, select to restart the system and press [Finish] to complete
the installation.

Windows Vista, Windows7 :
Step 1. Run the setup.exe program to start the installation.

Step 2. Click on [Next] to continue the procedure. If the Windows popup
"Windows can't verify the publisher of this driver software" message,
press "Install this driver software anyway" to continue the installation.

Step 3. Finally, select to restart the system and press [Finish] to complete
the installation.
--------------------------
Update Driver:
--------------------------
Windows 2000 , XP :
Step 1. Follow Step 2,3,4 described in [Setup at first time] above to complete
the procedure.

Windows Vista, Windows7 :
Step 1. Run setup.exe, it will remove the original driver in your system.

Step 2. Click "Next" to remove the original audio driver in your system.

Step 3. Once after the original driver removed , reboot the computer.

Step 4. Please go back to the new driver package after computer restarted.

Step 5. Run setup.exe, it will install the new audio driver then.
--------------------------
Remove Driver:
--------------------------
Windows 2000 , XP :
Step 1. Go to Start\Settings\Control Panel.

Step 2. Select [Add or Remove Programs] icon.

Step 3. Select "Realtek High Definition Audio Driver" and press [Remove]
button.

Step 4. Click on [Yes] to finish the uninstallation.

Step 5. At the end of the procedure, select to restart the system and press
[Finish] to complete the uninstallation.

Windows Vista, Windows7 :
Step 1. Go to Start\Settings\Control Panel.

Step 2. Select [Programs] icon.

Step 3. Select [Programs and Features] icon.

Step 4. Select "Realtek High Definition Audio Driver" and press [uninstall] button.

Step 5. Click on [Yes] to finish the uninstallation.

Step 6. At the end of the procedure, select to restart the system and press
[Finish] to complete the uninstallation.

BisonC07Install-D(0709062200)-V(6.32.710.1b)-S(4BA_YUV)-B(07)-C()-61_Agc6
Date : 2007/09/06/22:00
Versiion : Vista/XP32 : 6.32.710.1
note : Update 32 bit system file.
=======================================================================================================
BisonC07Install-D(0709140144)-V(6.32.710.1c)-S(4BA_YUV)-B(07)-C(Clevo)_CL
Date : 2007/09/14/01:44
Versiion : Vista/XP32(6.32.710.1), Vista/XP64(6.64.710.01)
note : Add 64 bit driver.
Reverse preview image.
Change preview application with snapshot & zoom in/out.
Add OEM.ini.
=======================================================================================================
BisonC07Install-D(0709172232)-V(6.32.710.1d)-S(4BA_YUV)-B(07)-C(Clevo)_CL
Date : 2007/09/17/22:32
Versiion : Vista/XP32(6.32.710.1), Vista/XP64(6.64.710.01)
note : Update OEM.ini for Zoom in/out function.
If you want Zoom in/out function, please set "ZoomIn_Out=yes".
If you don't want Zoom in/out function, please set "ZoomIn_Out=no".
=======================================================================================================
BisonC07Install-D(0710082338)-V(6.96.710.1e)-S(4BA_4AA+07)-C(Clevo)_CL
Date : 2007/10/08/23:38
Versiion : 4BA(2M) : Vista/XP32(6.32.710.1), Vista/XP64(6.64.710.1)
4AA(1.3M) : Vista/XP32(6.32.704.3), Vista/XP64(6.64.704.3)
note : Add 64 bit driver for 4BA+5607.
Add 4AA+5607 32/64 bit driver.

If you want Zoom in/out function, please set "ZoomIn_Out=yes".
If you don't want Zoom in/out function, please set "ZoomIn_Out=no".
=======================================================================================================
BisonC07Install-D(0710100022)-V(6.96.710.1f)-S(4BA_4AA+07)-C(Clevo)_CL
Date : 2007/10/10/00:22
Versiion : 4BA(2M) : Vista/XP32(6.32.710.1), Vista/XP64(6.64.710.1)
4AA(1.3M) : Vista/XP32(6.32.704.3), Vista/XP64(6.64.704.3)
note : Update 32/64 bit driver for 4BA+5607 to fix a/v unsync & quality of preview.
Update application to fix install issue & auto close issue.

OEM.ini with new function : [Preview]
ZoomIn_Out=yes yes : preview application with zoom in/zoom out function.
no : preview application without zoom in/zoom out function.
Close_AP_BeforeSleep=no yes : preview application will auto close before into S3/S4.
no : preview application won't auto close before into S3/S4.
DefaultFormat_YUY2_RGB24=yuy2 yuy2 : preview application will use YUY2 as default format.
rgb24: preview application will use RGB24 as default format.

[PowerSaving]
SelectiveSuspend=yes yes : support selective suspend.
no : not support selective suspend.

=======================================================================================================
BisonC07Install-D(0710112314)-V(6.96.710.1g)-S(4BA_4AA+07)-C(Clevo)_CL
Date : 2007/10/11/23:14
Versiion : 4BA(2M) : Vista/XP32(6.32.710.1), Vista/XP64(6.64.710.1)
4AA(1.3M) : Vista/XP32(6.32.710.1), Vista/XP64(6.64.710.1)
note : update 32/64 bit driver for 4AA+5607 with VID_5986&PID_0200.

=======================================================================================================
BisonC07Install-D(0710261658)-V(6.96.710.1h)-S(4BA_4AA+07)-C(Clevo)_CL
Date : 2007/10/26/16:58
Versiion : 4BA(2M) : Vista/XP32(6.32.710.1), Vista/XP64(6.64.710.1)
4AA(1.3M) : Vista/XP32(6.32.710.1), Vista/XP64(6.64.710.1)
note : Fix install issue for 4BA & 4AA + 07.
Update TSR to fix can't into C3 issue.

BisonC07Install-D(0906061730)-V(6.96.2728.01.1)-S()-C(Clevo)-CR
Date : 2009/06/06 17:30
Versiion : Vista/XP 32 (6.32.2728.01), Vista/XP 64 (6.64.2728.01)
note : Combine 3 driver for Win7 : S5K4AA+5607 & S5K4B1+5607 & S5K6AA+5608.
=============================================================================================
BisonC07Install-D(0906211639)-V(6.96.2728.02.1)-S()-C(Clevo)-CR
Date : 2009/06/21 16:39
Versiion : Vista/XP 32 (6.32.2728.02), Vista/XP 64 (6.64.2728.02)
note : Update inf settings to support more preview size.
Update BisonHK & system file to support Zoom function.
=============================================================================================
BisonC07Install-D(0906261441)-V(6.96.2728.02.2)-S()-C(Clevo)-CR
Date : 2009/06/26 14:41
Versiion : Vista/XP 32 (6.32.2728.02), Vista/XP 64 (6.64.2728.02)
note : Add support for 4CA+08 & 1330+07.
=============================================================================================
BisonC07Install-D(0907092153)-V(6.96.2728.03.1)-S()-C(Clevo)-CR
Date : 2009/07/09 21:53
Versiion : Vista/XP 32 (6.32.2728.03), Vista/XP 64 (6.64.2728.03)
note : Add the register in inf for C6 issue.
=============================================================================================
BisonC07Install-D(0907201524)-V(6.96.2728.03.2)-S()-C(Clevo)-CR
Date : 2009/07/20 15:24
Versiion : Vista/XP 32 (6.32.2728.03), Vista/XP 64 (6.64.2728.03)
note : Update 32bit pre-test system file of 4CA for cross noise & bad pixel issue.
Uninstall driver without reboot.
=============================================================================================
BisonC07Install-D(0907230003)-V(6.96.2728.03.3)-S()-C(Clevo)-CR
Date : 2009/07/23 00:03
Versiion : Vista/XP 32 (6.32.2728.03), Vista/XP 64 (6.64.2728.03)
note : Update 32bit pre-test system file of 4CA for cross noise & bad pixel issue.
Change shortcut behavior in the "Start Menu\Programs".
=============================================================================================
BisonC07Install-D(0907270953)-V(6.96.2728.04.1)-S()-C(Clevo)-CR-WHQL
Date : 2009/07/27 09:53
Versiion : Vista/XP 32 (6.32.2728.04), Vista/XP 64 (6.64.2728.04)
note : Update new driver with new link2008.
Disable TSR application before install driver for C6 issue.
Get logo.

R1.00.32.01-3 2009/7/24
Fix Win7 Publisher Unknow
======================
R1.00.32.01-2 2009/7/24
Fix D3E wake up Card Reader not work.

Product name Confidentiality level
UTPS CONFIDENTIAL
Product version
V100R001 Total 2 pages
UTPS13.001.07.03.335 Release Notes

1. New features
No Description
2. Improvements to previous
Version Features(New/Modify)
UTPS13.001.07.03
.335
1. Customize 20 kinds of language
2. Add APN
3. Delete option of “launch when device is available”
4. Support win7
5. Support fly-mode
3. Known limitations and issues
No Description
None None

Product: Intel(R) Chipset Device Software
Release: Production Version
Version: 9.1.1.1015
Target Chipset#: Intel(R) 5 Series/3400 Series Chipset

This document contains the following sections:

1. Overview
2. System Requirements
3. Contents of the Distribution Package
4. List of Available Command Line Flag Options
5. Contents of the Extracted Files
6. Installing the Software in Interactive Mode
7. Installing the Software in Silent Mode
8. Installing the INF Files Prior to OS Installation
8A. Installing the Windows* 2000 INF Files Prior
to OS Installation
8B. Installing the Windows* XP INF Files Prior
to OS Installation
8C. Installing the Windows Server* 2003 INF Files
Prior to OS Installation
8D. INSTALLING THE WINDOWS* VISTA INF FILES PRIOR
TO OS INSTALLATION
8E. INSTALLING THE WINDOWS SERVER* 2008 INF FILES PRIOR
TO OS INSTALLATION
9. Installing the INF Files After OS Installation
9A. Installing the Windows* 2000 INF Files After
OS Installation
9B. Installing the Windows* XP INF Files After
OS Installation
9C. Installing the Windows Server* 2003 INF Files
After OS Installation
9D. INSTALLING THE WINDOWS VISTA INF FILES AFTER
OS INSTALLATION
9E. INSTALLING THE Windows Server* 2008 INF FILES AFTER
OS INSTALLATION
10. Verifying Installation of the Software and
Identifying the Software Version Number
11. Troubleshooting

SiS 191/190 PCI Gigabit Ethernet Adapter Installation
for NetWare DOS ODI Driver

(1) Installation from CD ROM
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
1. Please make sure CD ROM player work fine under DOS environment.
2. Run INSTALL.BAT and press any key to accept the agreement.
3. Select "Client Installation".
4. Select "NetWare DOS/WINDOWS Client (VLM)".
5. Specify your target directory, default path is C:\NWCLIENT.
6. Allow system to modified your AUTOEXEC.BAT and CONFIG.SYS.
7. Select YES to install support for MS Windows, if you accept.
8. Move the highlight bar to Select the driver for your network
board and press <Enter>.
9. Put the released diskette into floppy disk and go to bottom
Select "OTHER DRIVERS" under Network Board.
10.Please insert SiS PCI Fast Ethernet adapter driver diskette into
floppy disk.
11.Specify the full path of ODI for DOS driver, Ex: A:\NWCLIENT.
12.Select "SiS 191/190 PCI Gigabit Ethernet".
13.Move to "Highlight here and press <Enter> to install".
14.Press <Enter> after you configure correctly, then installation
will copy necessary file to your hard disk.
15.Restart your system and connect to NetWare server.

------------------------
SiS19x PXE BootROM v1.3b
------------------------
(1)BootROM types :

for SiS191 --- (SiS965, SiS966, SiS968)
191pxe.18 -- SiS191 BootRom Hook Int18
191pxe.19 -- SiS191 BootRom Hook Int19
191pxe.BEV -- SiS191 BootRom use BEV

for SiS190 --- (SiS965L, SiS966L, SiS968L)
190pxe.18 -- SiS190 BootRom Hook Int18
190pxe.19 -- SiS190 BootRom Hook Int19
190pxe.BEV -- SiS190 BootRom use BEV
PS : Load MAC address from APC or EEPROM supported.

------------------------------------------------------------------
SiS 191/190 PCI Gigabit high speed Ethernet Adapter
for NDIS Driver

(1) Introduction
----------------
These driver programs comply with Microsoft's NDIS v2.0.1
specification.

(2) Rrelease Version
-----------------------
sis190.dos : v0.43

(3) Optional Parameters
-----------------------

MEDIATYPE - This parameter specifies the media type currently used.
If MEDIATYPE does not specified, it will auto detect the
media type.

Parameters List:
AUTO -- Auto-select media type.
UTP -- 10BaseT half duplex mode.
UTPFULL -- 10BaseT full duplex mode.
FAST -- 100BaseT half duplex mode.
FASTFULL -- 100BaseT full duplex mode.

Date Version Note
===============+========+========================================================================================
2007.10.08 041 1. Update Rx Status Descriptor definition.
2. Fix Protection Mode bug
3. Fix Fragmentation Issue.
4. support HW Radio On/Off.
5. Fix Sw Channel race condition.
6. support Mini-PCIe Card LED.
7. [Vista] support Active State Power Management.
8. Support Rate Adaptive, Antenna Diversity, Dynamic Initial Gain.
9. It's the first released beta version.

2007.10.13 042 1. Released for CCX4 test.

2007.10.18 043 1. Released for WHQL test.

2007.10.24 044 1. Rewrite Hw Key Content from low power state to active in order to avoid reset by Hw.

2007.10.26 045 1. [Vista] Fix out of Tx resource in SendRecv_Stress item of WHQL.

2007.11.07 046 1. Update formula of signal strength.

2007.11.16 047 1. Fix WPA2 Pre-Auth. PMK sometimes catche failed.
2. Support Inactive Power Save.

2007.11.29 048 1. For Power Consumption in disconnect situation.

2007.12.12 049 1. Fix incorrect memory copy to pass Scan_Cmn DTM test item.
2. Support Tx High Power Mechaniam.

2007.12.25 050 1. Fix Hot Plug then system crash issue.

2007.12.27 051 1. Improve Power Consumption in leisure time of connection.

2008.01.09 052 1. Fix disconnect from system sleep to awake.
2. Revise Antenna defination.

2008.01.16 053 1. Revise power save algorithm to avoid that
download file might spend very long time or disconnect.

2008.01.23 054 1. Support Customized ID.

2008.02.25 055 1. Revise Rate Adaptive Mechanism to improve long-range connection.

2008.03.13 056 1. Use Hw/Sw Rx evaluation ro improve antenna diversity Mechanism.
2. Support rate Adaptive in B mode.

2008.04.01 057 1. Released for WHQL test.
2. [Vista] Fix the bug of RF on/off functionality
between mobility center and HW options.

2008.04.21 058 1. [Vista] Fix WPS Feature Pack issue under Vista SP1

2008.04.23 059 1. support mesh network.

2008.04.24 060 1. Revise connect request for WPS Feature Pack

2008.06.06 061 1. Revise site survey behavior after the system is resuming.

2008.06.25 062 1. [Vista] Set Multicast_list to get DHCP correctly in DTM.

2008.06.27 063 1. [MacOS] Revise coding style for endian free.
2. Fix incorrect Rx FIFO status.

2008.07.01 064 1. Released for WLK 1.2
2. Add global domain which follow the country code,
otherwise active scan from ch1~11 and passive scan from ch12~14

Date Version Note
===============+========+========================================================================================
2007.10.08 041 1. Update Rx Status Descriptor definition.
2. Fix Protection Mode bug
3. Fix Fragmentation Issue.
4. support HW Radio On/Off.
5. Fix Sw Channel race condition.
6. support Mini-PCIe Card LED.
7. [Vista] support Active State Power Management.
8. Support Rate Adaptive, Antenna Diversity, Dynamic Initial Gain.
9. It's the first released beta version.

2007.10.13 042 1. Released for CCX4 test.

2007.10.18 043 1. Released for WHQL test.

2007.10.24 044 1. Rewrite Hw Key Content from low power state to active in order to avoid reset by Hw.

2007.10.26 045 1. [Vista] Fix out of Tx resource in SendRecv_Stress item of WHQL.

2007.11.07 046 1. Update formula of signal strength.

2007.11.16 047 1. Fix WPA2 Pre-Auth. PMK sometimes catche failed.
2. Support Inactive Power Save.

2007.11.29 048 1. For Power Consumption in disconnect situation.

2007.12.12 049 1. Fix incorrect memory copy to pass Scan_Cmn DTM test item.
2. Support Tx High Power Mechaniam.

2007.12.25 050 1. Fix Hot Plug then system crash issue.

2007.12.27 051 1. Improve Power Consumption in leisure time of connection.

2008.01.09 052 1. Fix disconnect from system sleep to awake.
2. Revise Antenna defination.

2008.01.16 053 1. Revise power save algorithm to avoid that
download file might spend very long time or disconnect.

2008.01.23 054 1. Support Customized ID.

2008.02.25 055 1. Revise Rate Adaptive Mechanism to improve long-range connection.

2008.03.13 056 1. Use Hw/Sw Rx evaluation ro improve antenna diversity Mechanism.
2. Support rate Adaptive in B mode.

2008.04.01 057 1. Released for WHQL test.
2. [Vista] Fix the bug of RF on/off functionality
between mobility center and HW options.

2008.04.21 058 1. [Vista] Fix WPS Feature Pack issue under Vista SP1

2008.04.23 059 1. support mesh network.

2008.04.24 060 1. Revise connect request for WPS Feature Pack

2008.06.06 061 1. Revise site survey behavior after the system is resuming.

2008.06.25 062 1. [Vista] Set Multicast_list to get DHCP correctly in DTM.

2008.06.27 063 1. [MacOS] Revise coding style for endian free.
2. Fix incorrect Rx FIFO status.

2008.07.01 064 1. Released for WLK 1.2
2. Add global domain which follow the country code,
otherwise active scan from ch1~11 and passive scan from ch12~14

Synaptics Pointing Device Driver Release Notes
Version 13.2.3
June 25, 2009
----------------------------------------------------------------------------
Overview
----------------------------------------------------------------------------
This document describes changes to the Synaptics TouchPad Driver
for Windows XP and Vista. Only external releases have been documented.
Other releases were for internal use, beta tests, or for specific customer
requests. These are not documented here.
----------------------------------------------------------------------------
Version 13.2.3 06/25/2009 (WinXP/Vista)
----------------------------------------------------------------------------
Bug Fixes
-Fixed lextra spaces before dots and dashes in Finish help.
-Added HelpID for demo ClickPad
-Added HelpText UI ClickZones with Middle Click
-Added HelpText UI ClickZones with Middle Click and Physical buttons
-Added settings for Show Video buttons and graphics for ClickPad 2.0 UI
-Added help text for clickpad 2.0
-Added one hot-key for button setting at OEM App.
-Fixed IDS_ENABLE stick hotkeys conflict issues.
-Added tap and double tap support for clickpad if one finger is rest in
the button zone, another finger does tap or double tap.
-Changed the default left and right buttons zone, and enabled tap and
double tap hack for clickpad.
-Set clickpad to true for 2 buttons clickpad.
-Make sure all HKLM are changed to HKR.
-We need to call IoSkipCurrentIrpStackLocation before calling
WdfDeviceWdmDispatchPreprocessedIrp if a new Irp is not created according
to specs., otherwise it causes a BSOD if verifier is enabled in 64-bit
Win7.
-Added more dependencies for Scroll item under pointer, Scroll selected
item, Enable reverse scrolling direction, and scrolling speed.
-Changed default settings.
-Added setting ControlBar1363 to demo in the trunk
-Excluded the ControlBar from showing up in our normal Mouse control panel
-1, Adjusted min amount of time the user will keep palm on the pad, before
triggering an action from 1000ms to 200ms. 2, Fixed PalmOnPad end action
was not fired because the stroke state was reset in secondary finger
packet. 3, Fixed PalmOnPad was not detected if there were 3 fingers
covering the TP.
-Updated for the SynSlidebar tester
-Converted old CPL tree to new CPL tree.
-Reorganized OEM inc files, and replaced all HKLM with HKR.
-Added document to describe adding new language support tasks
-updated configuration for PnP IDs
-Added branch for Gen3 demo.

How to use this RTLSetup Utility
---------------------------------
For Windows ME:

1. If the Operating System's New Hardware Wizard prompts you that
"New Hardware Found" for the "PCI Ethernet Controller", you should
click "Next" until "Finish" is clicked and without specifying
location of the driver. You will see the "PCI Ethernet Controller"
in the Device Manager.

2. Then you can install or update the NDIS driver with "setup" or
"setup -s" command:
a) setup: The InstallShield will prompt you the steps to install
or upgrade the driver.

b) setup -s: The InstallShield will complete the installation or
upgrade without prompting you any instruction.

You need to reboot the system immediately after the Install shield
completes the installation/upgrade.

3. Do not click "Cancel" during New Hardware Wizard searches for the
driver.

4. You can remove RTLSetup utility from Add/Remove Program Palette in
Control Panel, the InstallShield will prompt you the steps to remove
the driver. After remove the driver, please restart the system
immediately.

For Windows 2000/XP:

1. If the Operating System's Found New Hardware Wizard prompts you that
"New Hardware Found" for the "Ethernet Controller", you should click
"Next" until "Finish" is clicked and without specifying location of
the driver. You will see the "Ethernet Controller" in the Device
Manager.

2. Then you can install or upgrade the NDIS driver with "setup" or
"setup -s" command:
a) setup: The InstallShield will prompt you the steps to install
or upgrade the driver.

b) setup -s: The InstallShield will complete the installation or
upgrade without prompting you any instruction.

3. You can remove RTLSetup utility from Add/Remove Program Palette in
Control Panel, the InstallShield will prompt you the steps to remove
the driver. After remove the driver, please restart the system
immediately if you want your networking to be re-installed.

Alps Pointing-device Driver provides a convenient way to modify
setting for Alps Pointing-device. The Alps Pointing-device Driver
is compatible with most standard mice and similar pointing devices.
____________________________________________________________

CONTENTS:

1. Driver Installation for Windows 2000/XP
2. Using the Alps Pointing-device Property Sheets
3. Files On the Setup Disk
____________________________________________________________

1. Driver Installation for Windows 2000/XP

Use this procedure if you use Windows 2000/XP:
1) From the Start menu, select Settings, Control Panel.
2) Double-click Mouse to open Mouse Properties.
3) Select the Hardware tab, and then click Properties.
4) Select the Driver tab, and then click Change.
5) Click Next.
6) Select Display a list of the known drivers for this
device so that I can choose a specific driver, and
then click Next.
7) Click Have Disk.
8) Click Browse.
9) Choose specific directory name that you have copied
driver files.
10) Click Apfiltr.inf, and then click Open.
11) Click OK.
12) Click Alps Pointing-device, and then click Next.
13) Click Next to copy the driver files to your system.
14) Click Finish.
15) Click Close.
16) Click Yes, then restart PC automatically.

This document contains the following sections:

1. Overview
2. System Requirements
3. Contents of the Distribution Package
4. List of Available Command Line Flag Options
5. Contents of the Extracted Files
6. Installing the Software in Interactive Mode
7. Installing the Software in Silent Mode
8. Installing the INF Files Prior to OS Installation
8A. Installing the Windows* 2000 INF Files Prior
to OS Installation
8B. Installing the Windows* 98/Windows 98 SE/Windows* Me
INF Files Prior to OS Installation
8C. Installing the Windows* 95 INF Files Prior to OS
Installation
9. Installing the INF Files After OS Installation
9A. Installing the Windows* 2000 INF Files after
OS Installation
9B. Installing the Windows* 98/Windows* 98 SE/
Windows* Me/Windows* 95 INF Files after OS
Installation
10. Verifying Installation of the Software
11. Identifying the Software Version Number
12. Troubleshooting

Product name Confidentiality level
UTPS CONFIDENTIAL
Product version
V100R001 Total 2 pages
UTPS11.301.08.04.470 Release Notes

1. New features
No Description
None
2. Improvements to previous
Version Features(New/Modify)
UTPS
11.301.08.04.470
Customize the APN
Customize the usermanual
3. Known limitations and issues
No Description
None

ENE MR510 / CB-712/714 Full Package Release Note
*************************************************
Version : 3.00.07
Date : 2007-07-09

OS :
Vista64, Vista, WinXP64, WinXP, Win2000, WinME, Win9X

Product :
MR510 / CB-712/714 Setup Shield
All OS : 2.00.02
CB714 Cardbus INF Update
Vista/64 : 3.00.01
WinXP/2k : 3.00.01
WinXP64 : 2.00.08
WinME/9x : 2.00.01
MR510 / CB-712/714 SecureDigital Card Reader Driver
Vista64 : 2.00.04
Vista : 2.00.02
WinXP/2k : 2.00.02
WinXP64 : 1.07.00
WinME/9x : 1.01.00
MR510 / CB-712/714 Memory Stick Card Reader Driver
Vista64 : 2.00.03
Vista : 2.00.02
WinXP/2k : 2.00.02
WinXP64 : 1.07.00
WinME/9x : 1.01.00
MR510 / CB-712/714 SmartMedia/XD Card Reader Driver
Vista/64 : 2.00.02
WinXP/2k : 2.00.02
WinXP64 : 1.07.00
WinME/9x : 1.01.00

WHQL Vista32/64 submission ID :
Cardbus INF : 1233857
SecureDigital : 1256082
Memory Stick : 1256073
SmartMedia/XD : 1241407

WHQL WinXP submission ID :
Cardbus INF : 1241409
SecureDigital : 1241409
Memory Stick : 1241409
SmartMedia/XD : 1241409

WHQL WinXP64 submission ID :
Cardbus INF : 1048034
SecureDigital : 1048034
Memory Stick : 1048034
SmartMedia/XD : 1048034
Product : ENE MR510 / CB-712/714 Setup Shield
*******************************************
OS:
Vista64, Vista, WinXP64, WinXP, Win2000, WinME, Win9X
===== Release note =====
Version : 2.00.04 (SD), 2.00.03 (MS)
Date : 2007-07-09
1. For Vista64 ,new DMA way to support when system memory upper 4G.
===== Release note =====
Version : 2.00.02
Date : 2007-03-01
1. Fix bug --- Fix Program Compatibility Assistant (PCA) warning dialog issue when User Account Control (UAC) is enable.

Realtek Semiconductor Corp. AC'97 Sound System Software ver:A3.43
Installation and Setup

Driver & Application Installation/Removal Procedure For Realtek AC'97 Codec:
=================================================================================

<<< For Win2000/WinME/WinXP (WDM driver)/Win98 Gold(First Edition)/Win98SE >>>

---------------------------------------
Setup Driver/Application at first time:
---------------------------------------

Step 1. Before installing the Realtek AC'97 Drivers & Applications, Press the
[Cancel] button if Windows detect the PCI Multimedia Audio device.

Step 2. Insert the "Realtek AC'97 Drivers & Applications" CD into the CD-ROM
drive and run the setup.exe program to finish the installation.

Step 3. Click on [Next/OK/Go] to continue the procedure. If the Windows popup
"Digital Signature Not Found" message, press [Yes] to continue the
installation.

Step 4. Finally, select to restart the system and press [Finish] to complete
the installation.

The system will reload the drivers and do some adjustments in the INF
file if so required.

--------------------------
Update Driver/Application:
--------------------------

Step 1. Follow Step 2,3,4 described in [Setup at first time] above to complete
the procedure.

--------------------------
Remove Driver/Application:
--------------------------

Step 1. Go to Start\Settings\Control Panel.

Step 2. Select [Add/Remove Programs] icon.

Step 3. Select "Realtek AC'97 Drivers and Applications" and press [Change/Remove]
button.

Step 4. Click on [Next/OK/Go] to finish the uninstallation.

Step 5. At the end of the procedure, select to restart the system and press
[Finish] to complete the uninstallation.

<<< For WinNT 4.0 (NT4 driver) >>>

BisonC07Install-D(0904190142)-V(6.96.1728.01.1)-S(UMPC_C)-C(Clevo)-CR
Date : 2009/04/19 01:42
Versiion : Vista/XP 32 (6.32.1728.01), Vista/XP 64 (6.64.1728.01)
note : Combine 3 driver : S5K4AA+5607 & S5K4B1+5607 & S5K6AA+5608.
=============================================================================================
BisonC07Install-D(0904201120)-V(6.96.1728.02.1)-S(UMPC_C)-C(Clevo)-CR
Date : 2009/04/20 11:20
Versiion : Vista/XP 32 (6.32.1728.02), Vista/XP 64 (6.64.1728.02)
note : Update system file of 6AA with 24fps YUV setting.
=============================================================================================
BisonC07Install-D(0904222123)-V(6.96.1728.03.1)-S(UMPC_C)-C(Clevo)-CR
Date : 2009/04/22 21:23
Versiion : Vista/XP 32 (6.32.1728.03), Vista/XP 64 (6.64.1728.03)
note : Update system file of 6AA for 1024*768 support.
Turn off AE(auto exposure) with 6AA.
=============================================================================================
BisonC07Install-D(0904222313)-V(6.96.1728.04.1)-S(UMPC_C)-C(Clevo)-CR
Date : 2009/04/22 23:13
Versiion : Vista/XP 32 (6.32.1728.04), Vista/XP 64 (6.64.1728.04)
note : Update system file of 6AA for Brightness & Backlight & rotating issue.
=============================================================================================
BisonC07Install-D(0904231732)-V(6.96.1728.05.1)-S(UMPC_C)-C(Clevo)-CR
Date : 2009/04/23 17:32
Versiion : Vista/XP 32 (6.32.1728.05), Vista/XP 64 (6.64.1728.05)
note : Update system file of 6AA for garbage image issue while zoom in.
=============================================================================================
BisonC07Install-D(0904241309)-V(6.96.1728.06.1)-S(UMPC_C)-C(Clevo)-CR
Date : 2009/04/24 13:09
Versiion : Vista/XP 32 (6.32.1728.06), Vista/XP 64 (6.64.1728.06)
note : Update system file of 6AA for HR && VR & RGB gain & environment issue.
=============================================================================================
BisonC07Install-D(0905040203)-V(6.96.1728.07.1)-S(UMPC_C)-C(Clevo)-CR-WHQL
Date : 2009/05/02 19:36
Versiion : Vista/XP 32 (6.32.1728.07), Vista/XP 64 (6.64.1728.07)
note : Update system file of 6AA for NetMeeting issue.
Update new preview application for twice error message issue.
Update with logo.

English, French, German, Italian and Spanish