Axper XP-K8U-X Télécharger Pilotes, Manuel et BIOS

Support New revision K8 CPU

Contents
Motherboard Layout ......................................................................... 4
1. Product Introduction .................................................................. 5
1.1. Feature Summary ............................................................................. 5
1.2. I/O Back Panel and Connectors&Jumper Setting ........................... 6
1.2.1. I/O Back Panel ....................................................................................... 6
1.2.2. Connectors&Jumper Setting ................................................................ 6
2. Hardware Installation ............................................................... 10
2.1. Installation of a Socket 754 CPU and Fan Sink............................. 10
2.2. Installation of Memory..................................................................... 11
2.3. Installation of the Graphics Card ................................................... 12
3. BIOS Setup ............................................................................ 13
3.1. Setup Screen Features (BIOS version:F1) .................................... 13
3.2. Standard CMOS Features .............................................................. 14
3.3. Advanced BIOS Features ............................................................... 16
3.4. Integrated Peripherals .................................................................... 17
3.5. Power Management Setup ............................................................ 19
3.6. PnP/PCI Configurations ................................................................. 20
3.7. PC Health Status ............................................................................ 21
3.8. Frequency/Voltage Control ............................................................. 22
3.9. Load Fail-Safe Defaults ................................................................. 24
3.10. Load Optimized Defaults................................................................ 24
3.11. Set Supervisor/User Password ..................................................... 24
3.12. Save & Exit Setup ............................................................................ 24
3.13. Exit Without Saving.......................................................................... 24
4. Driver Installation ..................................................................... 25
5. Installation of SATA RAID Disks ............................................... 27
5.1. Configuring the System BIOS for the SATA Channel ..................... 27
5.2. Creating RAID Array ........................................................................ 29
5.3. Making the SATA RAID Driver Disk ................................................. 35
5.4. Loading the ULi M1689 Serial ATA Driver ....................................... 35

This integrated driver integrates
1. AGP driver V2.11 for Win2K/WinXP with M1563, V2.20 for WinXP/2003/x64 , V2.13Win98SE/WinME
2. IDE Cache Utility 1.06 for Win95 OSR2.1/Win98/Win98SE/WinME.
3. Mini-IDE driver 1.5.1.0 for Win2K/WinXP(WHQL).
4. FIR driver 1.150 for Win98(WHQL)/Win98SE(WHQL). FIR driver 1.141 for WinME(WHQL)
FIR driver 2.01 for Win2K(WHQL)/WinXP(WHQL).
5. Audio M5451 WDM driver 5.12.01.5260 for Win98SE/WinME(WHQL)/Win2K(WHQL)/WinXP(WHQL).
6. Audio M5455 WDM driver 5.12.01.7006 for Win98SE/WinME/Win2K/WinXP(WHQL), 5.12.01.7005 for x64.
7. Memory Stick driver 1.32.1018 for Win98SE/WinME,and 1.32.1030 for Win2000/WinXP.
8. SD/MMC driver 1.10.1018 for Win98SE/WinME,and 1.10.1040 for Win2000/WinXP.
9. LAN driver 3.40 for Win98/Win98SE/WinME/Win2K/2003/WinXP/x64.
10.USB 1.1 controller 1.03 for Win95 OSR2.1.
11.M7101 Patch 1.01 for Win95.
12.IRQ Miniport driver 0.1 for Windows95
13.USB 2.0 controller 1.73 for Win98SE/WinME/Win2K/2003/WinXP.
14.M5228 v 5.0.2.8 driver for NT4/98se/Me/2000/XP/2003/x64
15.M5281 v 5.0.2.8 driver for NT4/98se/Me v 5.0.2.9 for 2000/XP/2003/x64
16.M5287 v 6.2.0.3 driver for 2000/2003/XP v1.0.0.1 for x64
17.M5289 v 5.0.2.9 driver for NT4/98se/Me/2000/XP/2003 v1.0.0.1 for x64
18.M5461 v 5.0.1.0 (MS Inbox/function) driver for 2000_sp4 /XP/2003

How to use this RTLSetup Utility
---------------------------------
For Windows ME:

1. If the Operating System's New Hardware Wizard prompts you that
"New Hardware Found" for the "PCI Ethernet Controller", you should
click "Next" until "Finish" is clicked and without specifying
location of the driver. You will see the "PCI Ethernet Controller"
in the Device Manager.

2. Then you can install or update the NDIS driver with "setup" or
"setup -s" command:
a) setup: The InstallShield will prompt you the steps to install
or upgrade the driver.

b) setup -s: The InstallShield will complete the installation or
upgrade without prompting you any instruction.

You need to reboot the system immediately after the Install shield
completes the installation/upgrade.

3. Do not click "Cancel" during New Hardware Wizard searches for the
driver.

4. You can remove RTLSetup utility from Add/Remove Program Palette in
Control Panel, the InstallShield will prompt you the steps to remove
the driver. After remove the driver, please restart the system
immediately.

For Windows 2000/XP:

1. If the Operating System's Found New Hardware Wizard prompts you that
"New Hardware Found" for the "Ethernet Controller", you should click
"Next" until "Finish" is clicked and without specifying location of
the driver. You will see the "Ethernet Controller" in the Device
Manager.

2. Then you can install or upgrade the NDIS driver with "setup" or
"setup -s" command:
a) setup: The InstallShield will prompt you the steps to install
or upgrade the driver.

b) setup -s: The InstallShield will complete the installation or
upgrade without prompting you any instruction.

3. You can remove RTLSetup utility from Add/Remove Program Palette in
Control Panel, the InstallShield will prompt you the steps to remove
the driver. After remove the driver, please restart the system
immediately if you want your networking to be re-installed.

Driver & Application Installation/Removal Procedure For Realtek AC'97 Codec:
=================================================================================

<<< For Win2000/WinME/WinXP (WDM driver)/Win98 Gold(First Edition)/Win98SE >>>

---------------------------------------
Setup Driver/Application at first time:
---------------------------------------

Step 1. Before installing the Realtek AC'97 Drivers & Applications, Press the
[Cancel] button if Windows detect the PCI Multimedia Audio device.

Step 2. Insert the "Realtek AC'97 Drivers & Applications" CD into the CD-ROM
drive and run the setup.exe program to finish the installation.

Step 3. Click on [Next/OK/Go] to continue the procedure. If the Windows popup
"Digital Signature Not Found" message, press [Yes] to continue the
installation.

Step 4. Finally, select to restart the system and press [Finish] to complete
the installation.

The system will reload the drivers and do some adjustments in the INF
file if so required.

----------------
Setup for Manual
----------------
1. Double-click the "System" icon to open the "System Properties" dialog from Control Panel .
2. Choose "Hardware" tab and click the "Device Manager" button .
3. Please right-click mouse on "MultiMedia Audio Controller" and choose the "Properties" menu item
to show the driver details.
4. Click the "Driver" tab and then click the "Update Driver..." button for update.
5. Please follow the instructions of the "Upgrade Device Driver Wizard".
6. Choose "Search for a suitable driver for my device" and click the "Next" button.
7. Please specify the driver location/source and then click the "Next" button in this case,
"Specify a location" has been chosen.
8. If "Specify driver location" is chosen, the Wizard will ask for the path where the driver is located.
9. Click the "Next" button to install Audio Driver on "Driver Files Search Results".
10. If the "Digital Signature Not Found" dialog is opened, click the "Yes" button to continue
the Installation.
11. After completing the above steps, the drier has been installed into the system.
Please click "Finish" button to complete the installation.

--------------------------
Update Driver/Application:
--------------------------

Step 1. Follow Step 2,3,4 described in [Setup at first time] above to complete
the procedure.

--------------------------
Remove Driver/Application:
--------------------------

Step 1. Go to Start\Settings\Control Panel.

Step 2. Select [Add/Remove Programs] icon.

Step 3. Select "Realtek AC'97 Drivers" and press [Change/Remove]
button.

Step 4. Click on [Next/OK/Go] to finish the uninstallation.

Step 5. At the end of the procedure, select to restart the system and press
[Finish] to complete the uninstallation.
<<< For WinNT 4.0 (NT4 driver) >>>

---------------------------------------
Setup Driver/Application at first time:
---------------------------------------

Ignore Step 1, and follow the same procedure in Win2000/WinME/WinXP.

--------------------------
Update Driver/Application:
--------------------------

The same procedure in Win2000/WinME/WinXP.

--------------------------
Remove Driver/Application:
--------------------------

The same procedure in Win2000/WinME/WinXP.