BCM IN5598 Télécharger Pilotes, Manuel et BIOS

CONTENTS
1. INTRODUCTION
How to use this manual Page 8
Check your device items Page 8
2. FEATURES
Photo of the Motherboard Page 9
Features of the Motherboard Page 10
3. INSTALLATION
Motherboard Layout & Main Parts Page 12
Significant Parts List Page 13
Precaution Page 14
3.1 Slots And Connectors Page 15
3.2 CPU Page 16
3.2.1 Install CPU
3.2.2 Arrange Jumper Settings
3.2.3 Other Jumper Settings
3.3 System Memory ( DRAM ) Page 21
3.3.1 SIMM
3.3.2 Installation Procedure
3.3.3 Memory Module Combinations
3.4 Expansion Slots Page 23
3.5 Connectors Page 24
3.5.1 Primary IDE Connector
3.5.2 Secondary IDE Connector
3.5.3 Floppy Drive Connector
3.5.4 Power Input Connector
3.5.5 Front Panel Connectors
3.5.6 Back Panel Connectors
3.5.7 Additional Connectors
3.6 Ready to turn on power Page 30

CONTENTS
1. INTRODUCTION
How to use this manual Page 8
Check your device items Page 8
2. FEATURES
Photo of the Motherboard Page 9
Features of the Motherboard Page 10
3. INSTALLATION
Motherboard Layout & Main Parts Page 12
Significant Parts List Page 13
Precaution Page 14
3.1 Slots And Connectors Page 15
3.2 CPU Page 16
3.2.1 Install CPU
3.2.2 Arrange Jumper Settings
3.2.3 Other Jumper Settings
3.3 System Memory ( DRAM ) Page 21
3.3.1 SIMM
3.3.2 Installation Procedure
3.3.3 Memory Module Combinations
3.4 Expansion Slots Page 23
3.5 Connectors Page 24
3.5.1 Primary IDE Connector
3.5.2 Secondary IDE Connector
3.5.3 Floppy Drive Connector
3.5.4 Power Input Connector
3.5.5 Front Panel Connectors
3.5.6 Back Panel Connectors
3.5.7 Additional Connectors
3.6 Ready to turn on power Page 30

SiS IDE Drivers Installation Utility
====================================
---------------------------------------------------------------------
1. Uninstall SiS IDE DOS driver if you want to install SiS IDE
Netware driver.

---------------------------------------------------------------------
2. Under "IDE DEVICE DRIVER INSTALL UTILITY", user can install
SiS IDE DOS,
SiS IDE Windows 3.x,
SiS IDE Windows for Workgroup 3.11,
SiS IDE Netware 4.1
drivers directly from according "INSTALL DRIVER" menu.

3. Under "IDE DEVICE DRIVER INSTALL UTILITY", user can read
installation procedures for
SiS IDE Windows 95,
SiS IDE Windows NT 3.5x,
SiS IDE Windows NT 4.x,
SiS IDE OS2 Warp 3,
SiS IDE Netware 3.x,
drivers from according "INSTALL DRIVER" menu.
---------------------------------------------------------------------
4. Hard Drives' default wait states are set by using Hard Drive
internal information automatically. The recommended value table
for different mode Hard Drives is as follow :

Hard Disk Mode 4 3 2 1 0
==================================================
Recovery Time 1 3 8 A 0
Active Time 3 3 6 6 0
==================================================
Note that the range for Recovery Time is 0-F
and for Active Time is 0-7.

In config.sys file, users can use /A /R and /M parameters to set
the wait states and IDE BUS MASTER CONFIGURATION SPACE BASE ADDRESS
manually. For example:
"DEVICE=C:\SISIDE\SISDR.SYS /A3456 /R6543 /M:4000"
means active time for channel 0 master is 3*30ns
channel 0 slave is 4*30ns
channel 1 master is 5*30ns
channel 1 slave is 6*30ns

recovery time for channel 0 master is 6*30ns
channel 0 slave is 5*30ns
channel 1 master is 4*30ns
channel 1 slave is 3*30ns

CONTENTS
1. INTRODUCTION
How to use this manual Page 8
Check your device items Page 8
2. FEATURES
Photo of the Motherboard Page 9
Features of the Motherboard Page 10
3. INSTALLATION
Motherboard Layout & Main Parts Page 12
Significant Parts List Page 13
Precaution Page 14
3.1 Slots And Connectors Page 15
3.2 CPU Page 16
3.2.1 Install CPU
3.2.2 Arrange Jumper Settings
3.2.3 Other Jumper Settings
3.3 System Memory ( DRAM ) Page 21
3.3.1 SIMM
3.3.2 Installation Procedure
3.3.3 Memory Module Combinations
3.4 Expansion Slots Page 23
3.5 Connectors Page 24
3.5.1 Primary IDE Connector
3.5.2 Secondary IDE Connector
3.5.3 Floppy Drive Connector
3.5.4 Power Input Connector
3.5.5 Front Panel Connectors
3.5.6 Back Panel Connectors
3.5.7 Additional Connectors
3.6 Ready to turn on power Page 30

DRIVER INSTALLATION PROCEDURE

Click Start, then Settings, then Control Panel.

Start the "Display" applet program.

Select the "Settings" page, push the "Change Display Type" button.

Push the "Change" button in the "Adapter Type" area.

Push the "Have Disk" button and press "OK".

Specify the path to the new driver and press the
key:

Example 1: Insert the drivers disk in the A: floppy drive,
and enter A:\.

Example 2: Type in the name of the directory where you copied
the drivers, either on your local hard drive or
on a network share.

Example 3: If you're not sure exactly where the drivers are,
choose the "Browse..." button are find them.

The "Select Device" dialog box will appear. Select the adapter that
corresponds to the one you installed in your machine and click OK.

Windows 95 will copy the display drivers to the proper directories
on your system.

Continue choosing Close until asked to restart your machine from the
"Systems Settings Change" dialog box.

After the system has restarted, you can go back into the Display
applet and select alternate screen resolutions and color depths.