Comtrol VS1000 Download Drivers and Manual

Available 21 files for VS1000
Company
Comtrol
Categories
Other Peripherals
Model
Comtrol VS1000
Description
Device Driver
Operating Systems
Citrix WinFrame 1.6
Version Driver
2.35
Size Driver
372Kb
File Name
1800002b.exe
Info
Do NOT install this driver in Windows 2000/XP operating systems Driver for the Windows(R) NT Operating System, for:
InterchangeVS(TM) 1000 Series Communication Hub
InterChangeVS 2000 Series Analog Modem Hub
RocketPort Serial Hub
=================================================================
SCOPE AND LIMITS

Use this file to install the Comtrol software. This readme
file covers:

- Prerequisites
- Removing existing drivers and components
- Driver installation
- Installation troubleshooting
- Known software capabilities and limitations
- Technical Support contact information

VS1000/1100 and RocketPort Serial Hub Users:
For hardware installation or modem, printer, NT RAS (Remote
Access Service), or backup server installation and configuration,
see the Installation and Configuration Guide for your product.

VS2000 Users:
For NT RAS, modem reset, modem configuration, or backup server
installation and configuration, see the VS2000 VS-Link
Installation and Configuration Guide. For hardware installation
information, see the Hardware Installation Card that came with
the unit.

This product was developed and tested under Microsoft Windows NT
Release 4.0. Alternate instructions for Windows NT 3.51 are given
where needed. If you are using Citrix WinFrame, follow the
instructions for NT 3.51 and adapt as needed.
=================================================================
PREREQUISITES

This file assumes that you have already installed the Windows NT
operating system and that you have a basic understanding of
Windows NT operation.
=================================================================
REMOVING EXISTING DRIVER

Comtrol recommends removing older versions of the driver
before installing new releases.

1. Open the Control Panel and start the Network applet.

2. Select the Adapters tab.

3. Highlight Comtrol VS1000/VS2000.

4. Click the Remove button.

5. Close the Network applet.

6. Restart the server so that your changes take effect.
=================================================================
INSTALLING THE DRIVER

After you have extracted the driver files, follow these steps:

1. Right-click on the Network Neighborhood and select properties,
or open the Control Panel and start the Network applet.

2. NT 4.0: Select the Adapters tab and click the Add button.
NT 3.51: Click the Add Adapter button.

3. NT 4.0: Click the Have Disk button.
NT 3.51: Highlight Other and click Continue.

4. Enter the drive and directory path to the installation files
and click OK
Company
Comtrol
Categories
Other Peripherals
Model
Comtrol VS1000
Description
Device Driver
Operating Systems
Citrix WinFrame 1.7
Version Driver
2.35
Size Driver
372Kb
File Name
1800002b.exe
Info
Do NOT install this driver in Windows 2000/XP operating systems Driver for the Windows(R) NT Operating System, for:
InterchangeVS(TM) 1000 Series Communication Hub
InterChangeVS 2000 Series Analog Modem Hub
RocketPort Serial Hub
=================================================================
SCOPE AND LIMITS

Use this file to install the Comtrol software. This readme
file covers:

- Prerequisites
- Removing existing drivers and components
- Driver installation
- Installation troubleshooting
- Known software capabilities and limitations
- Technical Support contact information

VS1000/1100 and RocketPort Serial Hub Users:
For hardware installation or modem, printer, NT RAS (Remote
Access Service), or backup server installation and configuration,
see the Installation and Configuration Guide for your product.

VS2000 Users:
For NT RAS, modem reset, modem configuration, or backup server
installation and configuration, see the VS2000 VS-Link
Installation and Configuration Guide. For hardware installation
information, see the Hardware Installation Card that came with
the unit.

This product was developed and tested under Microsoft Windows NT
Release 4.0. Alternate instructions for Windows NT 3.51 are given
where needed. If you are using Citrix WinFrame, follow the
instructions for NT 3.51 and adapt as needed.
=================================================================
PREREQUISITES

This file assumes that you have already installed the Windows NT
operating system and that you have a basic understanding of
Windows NT operation.
=================================================================
REMOVING EXISTING DRIVER

Comtrol recommends removing older versions of the driver
before installing new releases.

1. Open the Control Panel and start the Network applet.

2. Select the Adapters tab.

3. Highlight Comtrol VS1000/VS2000.

4. Click the Remove button.

5. Close the Network applet.

6. Restart the server so that your changes take effect.
=================================================================
INSTALLING THE DRIVER

After you have extracted the driver files, follow these steps:

1. Right-click on the Network Neighborhood and select properties,
or open the Control Panel and start the Network applet.

2. NT 4.0: Select the Adapters tab and click the Add button.
NT 3.51: Click the Add Adapter button.

3. NT 4.0: Click the Have Disk button.
NT 3.51: Highlight Other and click Continue.

4. Enter the drive and directory path to the installation files
and click OK
Company
Comtrol
Categories
Other Peripherals
Model
Comtrol VS1000
Description
Device Driver
Operating Systems
Linux
Version Driver
1.05
Size Driver
60Kb
File Name
1800010a.gz
Company
Comtrol
Categories
Other Peripherals
Model
Comtrol VS1000
Description
Hardware Installation Guide
Operating Systems
Manual PDF
Version Manual
A
Size Manual
317Kb
File Name
6610hw.pdf
Info
Table of Contents
List of Tables ........................................................................................ 5
Introduction......................................................................................... 7
Product Overview ................................................................................... 7
Operating System Requirements .................................................... 7
Connectivity Requirements ............................................................. 7
Installation Overview............................................................................. 8
Initial Installation............................................................................ 8
Installing VS-Link Software Updates............................................. 8
Adding a VS1000 to an Existing Installation................................. 9
Adding a VS1100 to an Existing Installation................................. 9
“Hot-Swapping” a VS1000 ............................................................. 10
“Hot-Swapping” a VS1100 ............................................................. 10
Obtaining Software or Document Updates ......................................... 11
Comtrol Corporate Headquarters.................................................. 11
Comtrol Europe .............................................................................. 11
Technical Support ................................................................................. 12
Installing the Hardware.................................................................. 13
Hardware Installation Overview......................................................... 13
Installing the VS1000 Hardware......................................................... 13
Installing VS1100 Hardware ............................................................... 15
Power-On Diagnostics........................................................................... 17
Connecting Devices............................................................................... 19
Replacing Units in Service (“Hot-Swapping”) ..................................... 20
Building Cables.................................................................................. 21
Serial Cable Specifications................................................................... 21
Serial (RJ45) Connector Pinouts ................................................... 21
Building an RJ45 to DB25 Cable................................................... 22
Ethernet Cable Specifications.............................................................. 23
Company
Comtrol
Categories
Other Peripherals
Model
Comtrol VS1000
Description
Hardware Installation - Quick Reference
Operating Systems
Manual PDF
Version Manual
C
Size Manual
569Kb
File Name
6614.pdf
Info
InterChangeVS 1000
InterChangeVS 1100
Installation Reference Card

Installation Overview
Use this Reference Card to install the InterChangeVS
1000 base unit and InterChangeVS1100 port extenders.
To install the VS1000/VS1100 series, perform the
following procedures:
• Install the VS1000/VS1100 hardware and the
asynchronous RS-232 devices that you are
connecting to the VS1000/VS1100 serial ports
• Install the VS-Link software
• Configure your operating system to work with the
devices connected to the VS1000/VS1100
This is only an Installation Reference Card. See the
Installation and Configuration Guide for information
about installing the VS-Link software and other topics
not discussed in this card.

Installing VS1000 Hardware
Use the following procedure to connect the VS1000.
1. Record the model and serial numbers of the VS1000
in the event that you need to call technical support.
2. Optionally, mount the VS1000 into the rack using
the enclosed mounting brackets. The unit is
designed to install in the rack with the front or back
of the unit facing the front of the rack.
Warning: If mounting the VS1000 into a rack mount
unit, make sure the rack is not top heavy.
3. Connect the cable from the appropriate Ethernet
connection (10Base-T or AUI) on the VS1000 to your
server or Ethernet hub.
Note: Do not connect two VS1000 base units together.
If connecting the VS1000 directly to the server, an
Ethernet crossover cable is required. See the
Installation and Configuration Guide for details.
4. If installing only a VS1000, put the terminator plug
in the VS1100 connector of the VS1000 base unit.
Then go to the Power-On Diagnostics discussion.
5. If installing one or more VS1100 expansion units, go
to the Installing VS1100 Hardware discussion.

Installing VS1100 Hardware
Use the following procedure to connect InterChangeVS
1100 port extenders to the VS1000 base unit.
1. Record the serial numbers of the VS1100 units.
2. Optionally, mount the VS1100 port extenders into
the rack using the enclosed mounting brackets.
Warning: If mounting the VS1100 into a rack mount
unit, make sure the rack is not top heavy.
3. Connect the VS1100 device or devices to the VS1000
virtual server:
• Connect the cable shipped with the VS1100 from
the connector labeled VS1100 on the VS1000
unit to the INPUT connector on the VS1100.
• To connect additional VS1100 units, connect the
cable from the OUTPUT of one unit to the
INPUT of the next unit.
Note: You can connect up to three VS1100 port
extenders to one VS1000 base unit.
4. Install the terminator plug in the OUTPUT
connection of the last VS1100 in the installation.
5. Go to the Power-On Diagnostics discussion.
Company
Comtrol
Categories
Other Peripherals
Model
Comtrol VS1000
Description
Software Installation
Operating Systems
Manual PDF for Citrix WinFrame 1.6
Version Manual
A
Size Manual
776Kb
File Name
0000_a.pdf
Info
Table of Contents
List of Tables
Introduction
Scope ...................................................................................................... 9
Operating System Requirements .................................................... 9
Connectivity Requirements.............................................................. 9
Installation Overview....................................................................... 10
Initial Installation - Quick Reference ........................................... 10
Installing VS-Link Updates - Quick Reference ............................ 10
Adding a Unit to an Existing Installation - Quick Reference...... 11
“Hot-Swapping” Hardware - Quick Reference .............................. 11
Obtaining Software or Document Updates................................. 12
Comtrol Corporate Headquarters.................................................. 12
Comtrol Europe .............................................................................. 12
Technical Support............................................................................. 13
Windows NT
VS-Link Installation and Configuration Overview................... 15
Removing Existing VS-Link Software.......................................... 17
VS-Link Software Installation ....................................................... 19
Extracting the Files........................................................................ 19
Installing a New Version of VS-Link............................................. 20
Verifying the Installation............................................................... 29
Using VS-Link .................................................................................... 30
Accessing VS-Link Menus ............................................................. 31
Changing Configuration Parameters ............................................ 33
Configuring the Backup Server Feature ....................................... 34
Adding Units After the Initial Installation................................... 35
“Hot-Swapping” Units.................................................................... 36
Using Optional VS-Link Features................................................. 37
Company
Comtrol
Categories
Other Peripherals
Model
Comtrol VS1000
Description
Software Installation
Operating Systems
Manual PDF for Citrix WinFrame 1.7
Version Manual
A
Size Manual
776Kb
File Name
0000_a.pdf
Info
Table of Contents
List of Tables
Introduction
Scope ...................................................................................................... 9
Operating System Requirements .................................................... 9
Connectivity Requirements.............................................................. 9
Installation Overview....................................................................... 10
Initial Installation - Quick Reference ........................................... 10
Installing VS-Link Updates - Quick Reference ............................ 10
Adding a Unit to an Existing Installation - Quick Reference...... 11
“Hot-Swapping” Hardware - Quick Reference .............................. 11
Obtaining Software or Document Updates................................. 12
Comtrol Corporate Headquarters.................................................. 12
Comtrol Europe .............................................................................. 12
Technical Support............................................................................. 13
Windows NT
VS-Link Installation and Configuration Overview................... 15
Removing Existing VS-Link Software.......................................... 17
VS-Link Software Installation ....................................................... 19
Extracting the Files........................................................................ 19
Installing a New Version of VS-Link............................................. 20
Verifying the Installation............................................................... 29
Using VS-Link .................................................................................... 30
Accessing VS-Link Menus ............................................................. 31
Changing Configuration Parameters ............................................ 33
Configuring the Backup Server Feature ....................................... 34
Adding Units After the Initial Installation................................... 35
“Hot-Swapping” Units.................................................................... 36
Using Optional VS-Link Features................................................. 37
Company
Comtrol
Categories
Other Peripherals
Model
Comtrol VS1000
Description
Software Installation
Operating Systems
Manual PDF for Novell 4.11
Version Manual
A
Size Manual
469Kb
File Name
6610nw.pdf
Info
Novel v3.x and v4.x Table of Contents
List of Tables ........................................................................................ 5
Introduction......................................................................................... 7
Product Overview ................................................................................... 7
Operating System Requirements .................................................... 7
Connectivity Requirements ............................................................. 7
Installation Overview............................................................................. 8
Initial Installation............................................................................ 8
Installing VS-Link Software Updates............................................. 8
Adding a VS1000 to an Existing Installation................................. 9
Adding a VS1100 to an Existing Installation................................. 9
“Hot-Swapping” a VS1000 ............................................................. 10
“Hot-Swapping” a VS1100 ............................................................. 10
Obtaining Software or Document Updates ......................................... 11
Comtrol Corporate Headquarters.................................................. 11
Comtrol Europe .............................................................................. 11
Technical Support ................................................................................. 12
Novell NetWare.................................................................................. 13
Overview................................................................................................ 13
Software Installation............................................................................ 14
Before You Begin ............................................................................ 14
Extracting the Files........................................................................ 14
Creating an AIOVS1 Load Line........................................................... 15
NetWare Connect Installation and Configuration.............................. 16
Adding VS1000 Virtual Servers .................................................... 21
Adding VS1100 Expansion Units .................................................. 21
NIAS/MPR Installation and Configuration......................................... 22
Configuring Network Interfaces.................................................... 27
Configuring WAN Call Destinations............................................. 28
Company
Comtrol
Categories
Other Peripherals
Model
Comtrol VS1000
Description
Software Installation
Operating Systems
Manual PDF for Novell 5.0
Version Manual
A
Size Manual
469Kb
File Name
6610nw.pdf
Info
Novel v3.x and v4.x Table of Contents
List of Tables ........................................................................................ 5
Introduction......................................................................................... 7
Product Overview ................................................................................... 7
Operating System Requirements .................................................... 7
Connectivity Requirements ............................................................. 7
Installation Overview............................................................................. 8
Initial Installation............................................................................ 8
Installing VS-Link Software Updates............................................. 8
Adding a VS1000 to an Existing Installation................................. 9
Adding a VS1100 to an Existing Installation................................. 9
“Hot-Swapping” a VS1000 ............................................................. 10
“Hot-Swapping” a VS1100 ............................................................. 10
Obtaining Software or Document Updates ......................................... 11
Comtrol Corporate Headquarters.................................................. 11
Comtrol Europe .............................................................................. 11
Technical Support ................................................................................. 12
Novell NetWare.................................................................................. 13
Overview................................................................................................ 13
Software Installation............................................................................ 14
Before You Begin ............................................................................ 14
Extracting the Files........................................................................ 14
Creating an AIOVS1 Load Line........................................................... 15
NetWare Connect Installation and Configuration.............................. 16
Adding VS1000 Virtual Servers .................................................... 21
Adding VS1100 Expansion Units .................................................. 21
NIAS/MPR Installation and Configuration......................................... 22
Configuring Network Interfaces.................................................... 27
Configuring WAN Call Destinations............................................. 28
Company
Comtrol
Categories
Other Peripherals
Model
Comtrol VS1000
Description
Software Installation
Operating Systems
Manual PDF for Windows 2000
Version Manual
A
Size Manual
412Kb
File Name
2000144a.pdf
Info
RocketPort Serial Hub (RPSH) and VS1000/VS1100
Driver Installation with Windows 2000

Driver Requirements
This document discusses installing and configuring the VS1000 and RocketPort Serial Hub device driver for
the Windows 2000 operating system. The VS1000 or RocketPort Serial Hub requires at least one host server
running Windows® 2000.
Note: The driver for the RocketPort Serial Hub Si is different than the driver for the RocketPort Serial
Hub and they are NOT interchangeable.
For hardware specific information or the product overview, see the Hardware Installation documentation that
is available on the Comtrol media (diskette or CD) shipped with your product or download the current version
from the ftp/web site.
Driver updates can be downloaded at no charge from the Comtrol ftp/web site. Always check the web or ftp
sites to make sure that you have the current driver and documentation. Software downloaded from the ftp/
web site are self-extracting zipped files that you must extract before installing.
Driver Features
This driver has the following features:
• Can be installed on multiple servers.
• Supports up to 64 VS1000 or RocketPort Serial Hub devices per server.
Note: The critical limit is the number of ports your server can support. In most applications, this is
defined by the number of RAS port supported, which is typically 256 ports per primary server.
• Allows you to inter-mix VS1000 and RocketPort Serial Hub devices.
• Supports back up server
Connectivity Requirements
An Ethernet connection (10 Mbps), either to an Ethernet hub or to a network interface card (NIC) in the host
server. See the Hardware Installation documentation for information regarding hardware installation,
including building crossover cables.
Note: If connecting the RocketPort Serial Hub or VS1000 directly to the server NIC card, an Ethernet
crossover cable is required.
Upgrading from Windows 95/98 or Windows NT
If you are upgrading from another operating system, follow these steps:
Note: Do not use the Update Driver feature in the Device Manager to upgrade the driver.
1. Remove the driver from the Windows 95/98 or Windows NT operating system following the procedures
outlined in that software installation documentation.
2. Upgrade your system to Windows 2000.
Note: If you need information about re-installing devices, see the Hardware Installation documentation.
3. Use the Installing the Driver and Removing or Disabling the Device in Windows 2000 subsections to set
up the new driver.
Company
Comtrol
Categories
Other Peripherals
Model
Comtrol VS1000
Description
Software Installation
Operating Systems
Manual PDF for Windows 95
Version Manual
A
Size Manual
424Kb
File Name
2000060a.pdf
Info
RocketPort Serial Hub (RPSH) and
VS1000/VS1100 Driver Installation with
Windows 95/98

How to Use this Document
You can use the interactive Table of Contents to locate the information you need.
Driver Requirements
This document discusses installing and configuring the RocketPort Serial Hub and VS1000 device driver for
the Windows 9x platform. The RocketPort Serial Hub or VS1000 requires at least one host server running
Windows® 95 or Windows 98.
Note: The driver for the RocketPort Serial Hub Si is different than the driver for the RocketPort Serial
Hub/VS1000 and they are NOT interchangeable.
For hardware specific information or the product overview, see the Hardware Installation documentation that
is available on the Comtrol media (diskette or CD) shipped with your product or download the current version
from the ftp/web site.
Driver updates can be downloaded at no charge from the Comtrol ftp/web site. Always check the web or ftp
sites to make sure that you have the current driver and documentation. Software downloaded from the ftp/
web site are self-extracting zipped files that you must extract before installing.
Connectivity Requirements
An Ethernet connection (10 Mbps), either to an Ethernet hub or to a network interface card (NIC) in the host
server. See the Hardware Installation documentation for information regarding hardware installation,
including building crossover cables.
Note: If connecting the RocketPort Serial Hub or VS1000 directly to the server NIC card, an Ethernet
crossover cable is required.

Interactive Table of Contents
How to Use this Document................................................................................................................................ 1
Driver Requirements ......................................................................................................................................... 1
Connectivity Requirements.............................................................................................................................. 1
Installing the Device Driver............................................................................................................................. 3
Configuring the Device...................................................................................................................................... 9
Configuring Modems........................................................................................................................................ 17
Verifying the Ports are Available ................................................................................................................... 19
Troubleshooting ................................................................................................................................................ 19
Removing the RocketPort Serial Hub or VS1000/VS1100......................................................................... 19
Removing a Device ........................................................................................................................................... 19
Removing the Driver........................................................................................................................................ 19
Installing Additional Devices......................................................................................................................... 19
Using Test Terminal (WCOM32) to Test Ports ............................................................................................. 20
Contacting Technical Support ........................................................................................................................ 22
Company
Comtrol
Categories
Other Peripherals
Model
Comtrol VS1000
Description
Software Installation
Operating Systems
Manual PDF for Windows 98
Version Manual
A
Size Manual
424Kb
File Name
2000060a.pdf
Info
RocketPort Serial Hub (RPSH) and
VS1000/VS1100 Driver Installation with
Windows 95/98

How to Use this Document
You can use the interactive Table of Contents to locate the information you need.
Driver Requirements
This document discusses installing and configuring the RocketPort Serial Hub and VS1000 device driver for
the Windows 9x platform. The RocketPort Serial Hub or VS1000 requires at least one host server running
Windows® 95 or Windows 98.
Note: The driver for the RocketPort Serial Hub Si is different than the driver for the RocketPort Serial
Hub/VS1000 and they are NOT interchangeable.
For hardware specific information or the product overview, see the Hardware Installation documentation that
is available on the Comtrol media (diskette or CD) shipped with your product or download the current version
from the ftp/web site.
Driver updates can be downloaded at no charge from the Comtrol ftp/web site. Always check the web or ftp
sites to make sure that you have the current driver and documentation. Software downloaded from the ftp/
web site are self-extracting zipped files that you must extract before installing.
Connectivity Requirements
An Ethernet connection (10 Mbps), either to an Ethernet hub or to a network interface card (NIC) in the host
server. See the Hardware Installation documentation for information regarding hardware installation,
including building crossover cables.
Note: If connecting the RocketPort Serial Hub or VS1000 directly to the server NIC card, an Ethernet
crossover cable is required.

Interactive Table of Contents
How to Use this Document................................................................................................................................ 1
Driver Requirements ......................................................................................................................................... 1
Connectivity Requirements.............................................................................................................................. 1
Installing the Device Driver............................................................................................................................. 3
Configuring the Device...................................................................................................................................... 9
Configuring Modems........................................................................................................................................ 17
Verifying the Ports are Available ................................................................................................................... 19
Troubleshooting ................................................................................................................................................ 19
Removing the RocketPort Serial Hub or VS1000/VS1100......................................................................... 19
Removing a Device ........................................................................................................................................... 19
Removing the Driver........................................................................................................................................ 19
Installing Additional Devices......................................................................................................................... 19
Using Test Terminal (WCOM32) to Test Ports ............................................................................................. 20
Contacting Technical Support ........................................................................................................................ 22
Company
Comtrol
Categories
Other Peripherals
Model
Comtrol VS1000
Description
Software Installation
Operating Systems
Manual PDF for Windows NT 3.51
Version Manual
A
Size Manual
776Kb
File Name
0000_a.pdf
Info
Table of Contents
List of Tables
Introduction
Scope ...................................................................................................... 9
Operating System Requirements .................................................... 9
Connectivity Requirements.............................................................. 9
Installation Overview....................................................................... 10
Initial Installation - Quick Reference ........................................... 10
Installing VS-Link Updates - Quick Reference ............................ 10
Adding a Unit to an Existing Installation - Quick Reference...... 11
“Hot-Swapping” Hardware - Quick Reference .............................. 11
Obtaining Software or Document Updates................................. 12
Comtrol Corporate Headquarters.................................................. 12
Comtrol Europe .............................................................................. 12
Technical Support............................................................................. 13
Windows NT
VS-Link Installation and Configuration Overview................... 15
Removing Existing VS-Link Software.......................................... 17
VS-Link Software Installation ....................................................... 19
Extracting the Files........................................................................ 19
Installing a New Version of VS-Link............................................. 20
Verifying the Installation............................................................... 29
Using VS-Link .................................................................................... 30
Accessing VS-Link Menus ............................................................. 31
Changing Configuration Parameters ............................................ 33
Configuring the Backup Server Feature ....................................... 34
Adding Units After the Initial Installation................................... 35
“Hot-Swapping” Units.................................................................... 36
Using Optional VS-Link Features................................................. 37
Company
Comtrol
Categories
Other Peripherals
Model
Comtrol VS1000
Description
Device Driver
Operating Systems
Novell 4.11
Version Driver
1.01
Size Driver
77Kb
File Name
6612.zip
Info
Change History for the aiovs1.nlm
InterChangeVS(TM) 1000/1100

Version Date Description
=============================================================================

1.01 10/01/97 Correct problem with help and GetPortsRollCall.
1.00 9/25/97 Initial Version

Notes:
======

The files included are as follows.

1) aiovs1.nlm - InterChangeVS 1000/1100 executable.

2) aiovs1.txt - README file for the InterChangeVS 1000/1100.

3) aiovs1.adi - Novell AIO configuration file that is used by the
Novell installation programs (i.e. inetcfg or nwccon).

4) aiovs1.pdi - Novell Protocol configuration file that is used by the
Novell installation programs (i.e. inetcfg or nwccon).

5) vs1man.nlm - Diagnostic tool for the InterChangeVS 1000/1100.

6) vs1man.txt - README file for the Diagnostic/Management tool.

7) vs1trace.nlm - Trace tool for the InterChangeVS 1000/1100.

8) vs1trace.txt - README file for the Trace tool.

The aiovs1 conforms to Version 1.1 of the NetWare AIO Driver
Company
Comtrol
Categories
Other Peripherals
Model
Comtrol VS1000
Description
Device Driver
Operating Systems
Novell 5.0
Version Driver
1.01
Size Driver
77Kb
File Name
6612.zip
Info
Change History for the aiovs1.nlm
InterChangeVS(TM) 1000/1100

Version Date Description
=============================================================================

1.01 10/01/97 Correct problem with help and GetPortsRollCall.
1.00 9/25/97 Initial Version

Notes:
======

The files included are as follows.

1) aiovs1.nlm - InterChangeVS 1000/1100 executable.

2) aiovs1.txt - README file for the InterChangeVS 1000/1100.

3) aiovs1.adi - Novell AIO configuration file that is used by the
Novell installation programs (i.e. inetcfg or nwccon).

4) aiovs1.pdi - Novell Protocol configuration file that is used by the
Novell installation programs (i.e. inetcfg or nwccon).

5) vs1man.nlm - Diagnostic tool for the InterChangeVS 1000/1100.

6) vs1man.txt - README file for the Diagnostic/Management tool.

7) vs1trace.nlm - Trace tool for the InterChangeVS 1000/1100.

8) vs1trace.txt - README file for the Trace tool.

The aiovs1 conforms to Version 1.1 of the NetWare AIO Driver
Company
Comtrol
Categories
Other Peripherals
Model
Comtrol VS1000
Description
Device Driver
Operating Systems
Windows 2000
Version Driver
2.40
Size Driver
362Kb
File Name
1800036a.exe
Info
Do NOT install this driver in a Windows XP or NT system. VSLink series Device Driver
for the Windows(TM) 2000 Operating System
Intel x86 Platform
==================================================================
SCOPE AND LIMITS

You can use this file or the Software Installation and
Configuration documentation to install the Comtrol VSLink software
for the following products:

- Interchange (TM) VS 1000
- RocketPort Serial Hub 4-port
- RocketPort Serial Hub 8-port

This software does NOT support the RocketPort Serial Hub Si.

This driver is for Windows 2000 Operating System only. Previous
versions of Windows cannot use this driver. See the Comtrol FTP
site for other Comtrol drivers.

This readme file covers:

- Prerequisites
- VS and RPSH installation
- Verifying the installation
- Upgrading the driver
- Removing VS and RPSH devices
- Known software capabilities and limitations
- Technical support contact information

For hardware installation or modem / printer installation and
configuration, see the Software Installation and Configuration
Guide. Additional information is also available after the
installation is complete by selecting help in the setup program.
You can view the help information before installation by running
WINHELP vssetup.hlp.

This driver was developed and tested under Microsoft Windows 2000.

=================================================================
PREREQUISITES

This file assumes that you have already installed the Windows
2000 operating system and that you have a basic understanding of
Windows 2000 operation.

To Install and manage a Comtrol Device, you must be logged into
the system with Administrator Access.
=================================================================
INSTALLING THE SOFTWARE

1. Right click on the My Computer Icon and select Properties from
the menu.

2. Select the Hardware tab, then click the Hardware Wizard button.

3. Click Next.

4. In the Hardware Wizard screens, select Add/Troubleshoot a
device. Windows will search for new Plug and Play
hardware to install.

5. Select "Add a new device" and click Next.

6. Select "No, I want to select the hardware from a list", then
select "Multi-port serial adapter" as the type of hardware
to install.

7. Press the "Have Disk" button, and point the installation to the
install disk or directory where you extracted the VSLink
assembly (eg. C:\COMTROL).
Company
Comtrol
Categories
Other Peripherals
Model
Comtrol VS1000
Description
Device Driver
Operating Systems
Windows 95
Version Driver
1.10
Size Driver
308Kb
File Name
1800034c.exe
Info
Do NOT install this driver in Windows 2000/XP operating systems. RocketPort Serial Hub Windows 95/98 Driver Revision History
=====================================================================

V1.09 - 7-10-01
Updated WCOM32.exe and Portmon.exe as well as adding Portmon.cnt
and WCOM32.cnt for the help files. Wcom32.hlp was added to replace
WCOM.hlp and the Readme file as updated to show the correct Area
code for the US phone numbers.

v1.08 - 11-1-00
Update the Setup Help file, 8000126, from version 1.00 to
version 1.01. Added a .cnt table of contents file.
Updated Tech Support contact info.
v1.07 - 10-19-00
Fixes for incidents 78 and 497.

Incident 78 "VS2000 support indicated". The "Add New Hardware"
Wizard presented VS2000 as a configuration option. VS2000 is
not supported by this driver. The option was removed.

Incident 497, invalid device names presented in configuration
screen. Corrected.

v1.06 - 9-20-00
Add "wait for tx" support. Wait for transmit complete is a standard
feature that was missing from the original implementation of this driver.
v1.05 -
Fixed Null stripping

v1.04 -
01-19-99
Added optional setup at the time of program group creation.
Modified the device manager property page.
Changed the graphic in the setup program.
Removed VS2000 from the selectable devices.
Changed readme.txt to readme.doc
12-28-99
New peer, portmon, and wcom because of Win2000 changes.

v1.02 - 12-22-99
Bug fixes for initial release.

v1.01 - 5-11-99
Recompile in house.

v1.00 - 3-29-99
initial creation.
Company
Comtrol
Categories
Other Peripherals
Model
Comtrol VS1000
Description
Device Driver
Operating Systems
Windows 98
Version Driver
1.10
Size Driver
308Kb
File Name
1800034c.exe
Info
Do NOT install this driver in Windows 2000/XP operating systems. RocketPort Serial Hub Windows 95/98 Driver Revision History
=====================================================================

V1.09 - 7-10-01
Updated WCOM32.exe and Portmon.exe as well as adding Portmon.cnt
and WCOM32.cnt for the help files. Wcom32.hlp was added to replace
WCOM.hlp and the Readme file as updated to show the correct Area
code for the US phone numbers.

v1.08 - 11-1-00
Update the Setup Help file, 8000126, from version 1.00 to
version 1.01. Added a .cnt table of contents file.
Updated Tech Support contact info.
v1.07 - 10-19-00
Fixes for incidents 78 and 497.

Incident 78 "VS2000 support indicated". The "Add New Hardware"
Wizard presented VS2000 as a configuration option. VS2000 is
not supported by this driver. The option was removed.

Incident 497, invalid device names presented in configuration
screen. Corrected.

v1.06 - 9-20-00
Add "wait for tx" support. Wait for transmit complete is a standard
feature that was missing from the original implementation of this driver.
v1.05 -
Fixed Null stripping

v1.04 -
01-19-99
Added optional setup at the time of program group creation.
Modified the device manager property page.
Changed the graphic in the setup program.
Removed VS2000 from the selectable devices.
Changed readme.txt to readme.doc
12-28-99
New peer, portmon, and wcom because of Win2000 changes.

v1.02 - 12-22-99
Bug fixes for initial release.

v1.01 - 5-11-99
Recompile in house.

v1.00 - 3-29-99
initial creation.
Company
Comtrol
Categories
Other Peripherals
Model
Comtrol VS1000
Description
Device Driver
Operating Systems
Windows NT 3.51
Version Driver
2.35
Size Driver
372Kb
File Name
1800002b.exe
Info
Do NOT install this driver in Windows 2000/XP operating systems. Driver for the Windows(R) NT Operating System, for:
InterchangeVS(TM) 1000 Series Communication Hub
InterChangeVS 2000 Series Analog Modem Hub
RocketPort Serial Hub
=================================================================
SCOPE AND LIMITS

Use this file to install the Comtrol software. This readme
file covers:

- Prerequisites
- Removing existing drivers and components
- Driver installation
- Installation troubleshooting
- Known software capabilities and limitations
- Technical Support contact information

VS1000/1100 and RocketPort Serial Hub Users:
For hardware installation or modem, printer, NT RAS (Remote
Access Service), or backup server installation and configuration,
see the Installation and Configuration Guide for your product.

VS2000 Users:
For NT RAS, modem reset, modem configuration, or backup server
installation and configuration, see the VS2000 VS-Link
Installation and Configuration Guide. For hardware installation
information, see the Hardware Installation Card that came with
the unit.

This product was developed and tested under Microsoft Windows NT
Release 4.0. Alternate instructions for Windows NT 3.51 are given
where needed. If you are using Citrix WinFrame, follow the
instructions for NT 3.51 and adapt as needed.
=================================================================
PREREQUISITES

This file assumes that you have already installed the Windows NT
operating system and that you have a basic understanding of
Windows NT operation.
=================================================================
REMOVING EXISTING DRIVER

Comtrol recommends removing older versions of the driver
before installing new releases.

1. Open the Control Panel and start the Network applet.

2. Select the Adapters tab.

3. Highlight Comtrol VS1000/VS2000.

4. Click the Remove button.

5. Close the Network applet.

6. Restart the server so that your changes take effect.
=================================================================
INSTALLING THE DRIVER

After you have extracted the driver files, follow these steps:

1. Right-click on the Network Neighborhood and select properties,
or open the Control Panel and start the Network applet.

2. NT 4.0: Select the Adapters tab and click the Add button.
NT 3.51: Click the Add Adapter button.

3. NT 4.0: Click the Have Disk button.
NT 3.51: Highlight Other and click Continue.

4. Enter the drive and directory path to the installation files
and click OK
Company
Comtrol
Categories
Other Peripherals
Model
Comtrol VS1000
Description
Device Driver
Operating Systems
Windows NT 3.51
Version Driver
2.37
Size Driver
372Kb
File Name
1800002c.exe
Info
Do NOT install this driver in Windows 2000/XP operating systems. Driver for the Windows(R) NT Operating System, for:
InterchangeVS(TM) 1000 Series Communication Hub
InterChangeVS 2000 Series Analog Modem Hub
RocketPort Serial Hub
=================================================================
SCOPE AND LIMITS

Use this file to install the Comtrol software. This readme
file covers:

- Prerequisites
- Removing existing drivers and components
- Driver installation
- Installation troubleshooting
- Known software capabilities and limitations
- Technical Support contact information

VS1000/1100 and RocketPort Serial Hub Users:
For hardware installation or modem, printer, NT RAS (Remote
Access Service), or backup server installation and configuration,
see the Installation and Configuration Guide for your product.

VS2000 Users:
For NT RAS, modem reset, modem configuration, or backup server
installation and configuration, see the VS2000 VS-Link
Installation and Configuration Guide. For hardware installation
information, see the Hardware Installation Card that came with
the unit.

This product was developed and tested under Microsoft Windows NT
Release 4.0. Alternate instructions for Windows NT 3.51 are given
where needed. If you are using Citrix WinFrame, follow the
instructions for NT 3.51 and adapt as needed.
=================================================================
PREREQUISITES

This file assumes that you have already installed the Windows NT
operating system and that you have a basic understanding of
Windows NT operation.
=================================================================
REMOVING EXISTING DRIVER

Comtrol recommends removing older versions of the driver
before installing new releases.

1. Open the Control Panel and start the Network applet.

2. Select the Adapters tab.

3. Highlight Comtrol VS1000/VS2000.

4. Click the Remove button.

5. Close the Network applet.

6. Restart the server so that your changes take effect.
=================================================================
INSTALLING THE DRIVER

After you have extracted the driver files, follow these steps:

1. Right-click on the Network Neighborhood and select properties,
or open the Control Panel and start the Network applet.

2. NT 4.0: Select the Adapters tab and click the Add button.
NT 3.51: Click the Add Adapter button.

3. NT 4.0: Click the Have Disk button.
NT 3.51: Highlight Other and click Continue.

4. Enter the drive and directory path to the installation files
and click OK
Company
Comtrol
Categories
Other Peripherals
Model
Comtrol VS1000
Description
Device Driver
Operating Systems
Windows NT4
Version Driver
2.37
Size Driver
372Kb
File Name
1800002c.exe
Info
Do NOT install this driver in Windows 2000/XP operating systems. Driver for the Windows(R) NT Operating System, for:
InterchangeVS(TM) 1000 Series Communication Hub
InterChangeVS 2000 Series Analog Modem Hub
RocketPort Serial Hub
=================================================================
SCOPE AND LIMITS

Use this file to install the Comtrol software. This readme
file covers:

- Prerequisites
- Removing existing drivers and components
- Driver installation
- Installation troubleshooting
- Known software capabilities and limitations
- Technical Support contact information

VS1000/1100 and RocketPort Serial Hub Users:
For hardware installation or modem, printer, NT RAS (Remote
Access Service), or backup server installation and configuration,
see the Installation and Configuration Guide for your product.

VS2000 Users:
For NT RAS, modem reset, modem configuration, or backup server
installation and configuration, see the VS2000 VS-Link
Installation and Configuration Guide. For hardware installation
information, see the Hardware Installation Card that came with
the unit.

This product was developed and tested under Microsoft Windows NT
Release 4.0. Alternate instructions for Windows NT 3.51 are given
where needed. If you are using Citrix WinFrame, follow the
instructions for NT 3.51 and adapt as needed.
=================================================================
PREREQUISITES

This file assumes that you have already installed the Windows NT
operating system and that you have a basic understanding of
Windows NT operation.
=================================================================
REMOVING EXISTING DRIVER

Comtrol recommends removing older versions of the driver
before installing new releases.

1. Open the Control Panel and start the Network applet.

2. Select the Adapters tab.

3. Highlight Comtrol VS1000/VS2000.

4. Click the Remove button.

5. Close the Network applet.

6. Restart the server so that your changes take effect.
=================================================================
INSTALLING THE DRIVER

After you have extracted the driver files, follow these steps:

1. Right-click on the Network Neighborhood and select properties,
or open the Control Panel and start the Network applet.

2. NT 4.0: Select the Adapters tab and click the Add button.
NT 3.51: Click the Add Adapter button.

3. NT 4.0: Click the Have Disk button.
NT 3.51: Highlight Other and click Continue.

4. Enter the drive and directory path to the installation files
and click OK
HelpDrivers Since March 2000