Fujifilm FD-A1-FD-A2 Télécharger Pilotes
Disponibles 3 fichiers pour FD-A1-FD-A2
Constructeur
Fujifilm
Catégorie
Appareils photo et vidéo numériques
Modèle
Fujifilm FD-A1-FD-A2
Description
Drivers
Système d'exploitation
Windows 2000
Taille
1Mb
Nom de fichier
ver350_2000.exe
Informations
1. SOFTWARE REVISION HISTORY
2. GETTING READY
3. KNOWN ISSUES
4. IMPORTANT NOTES (CAUTION)
5. NOTES
1. ===[SOFTWARE REVISION HISTORY]===
Rev. Date and Comments
--------- -----------------------------------------------------
3.50.18 March 31, 2000
FlashPath for SmartMedia.
1. Supports SmartMedia sizes:
64MB, 32MB, 16MB, 8MB, 4MB and 2MB
2. Software version for support of FlashPath for
SmartMedia on:
IBM PC/AT compatible PCs (with a single Intel
x86 or fully compatible CPU) running:
* Windows 2000
- single Intel x86 (Pentium 133 MHz or higher) or
fully compatible CPU:
English, Japanese, French, Spanish, and German.
NOTE: You must uninstall any prior ALPHA, BETA, or
"RELEASE CANDIDATE" version of "FlashPath",
BEFORE installing this version.
PLEASE ALSO NOTE THAT WHEN YOU INSTALL "FLASHPATH" ON
THE ABOVE LANGUAGE VERSIONS OF THE OPERATINGS SYSTEMS,
THAT THE FLASHPATH "USER INTERFACE" AND ALL "FLASHPATH"
MESSAGES ARE IN THE ENGLISH LANGUAGE.
2. ===[GETTING READY]===
Please read the following information before installing
FlashPath.
A. IBM PC/AT COMPATIBLE PC - SYSTEM REQUIREMENTS
1. HARDWARE REQUIREMENTS:
a. IBM PC/AT compatible PCs with a single Intel x86
(Pentium 133 MHz or higher) or fully compatible CPU.
1. Does NOT work on multiple CPU systems.
2. Does NOT work on RISC based systems
(Alpha AXP, MIPS R4x00, or PowerPCs).
b. At least a single 3.5 inch floppy disk drive:
3.5 inch, 1.44MB floppy disk drive, or a
3.5 inch Japanese 3-mode floppy disk drive.
DOES NOT SUPPORT:
- LS-120 SuperDrives (120mb / 1.44mb).
- External floppy drives (USB, serial, parallel
or other external interface).
2. OPERATING SYSTEMS:
a. Microsoft Windows 2000 (single Intel x86
(Pentium 133 MHz or higher) or fully compatible CPU).
NOTE:
In order to install or uninstall FlashPath software
on Windows 2000, you must be a user with
"Administrator Privileges".
2. GETTING READY
3. KNOWN ISSUES
4. IMPORTANT NOTES (CAUTION)
5. NOTES
1. ===[SOFTWARE REVISION HISTORY]===
Rev. Date and Comments
--------- -----------------------------------------------------
3.50.18 March 31, 2000
FlashPath for SmartMedia.
1. Supports SmartMedia sizes:
64MB, 32MB, 16MB, 8MB, 4MB and 2MB
2. Software version for support of FlashPath for
SmartMedia on:
IBM PC/AT compatible PCs (with a single Intel
x86 or fully compatible CPU) running:
* Windows 2000
- single Intel x86 (Pentium 133 MHz or higher) or
fully compatible CPU:
English, Japanese, French, Spanish, and German.
NOTE: You must uninstall any prior ALPHA, BETA, or
"RELEASE CANDIDATE" version of "FlashPath",
BEFORE installing this version.
PLEASE ALSO NOTE THAT WHEN YOU INSTALL "FLASHPATH" ON
THE ABOVE LANGUAGE VERSIONS OF THE OPERATINGS SYSTEMS,
THAT THE FLASHPATH "USER INTERFACE" AND ALL "FLASHPATH"
MESSAGES ARE IN THE ENGLISH LANGUAGE.
2. ===[GETTING READY]===
Please read the following information before installing
FlashPath.
A. IBM PC/AT COMPATIBLE PC - SYSTEM REQUIREMENTS
1. HARDWARE REQUIREMENTS:
a. IBM PC/AT compatible PCs with a single Intel x86
(Pentium 133 MHz or higher) or fully compatible CPU.
1. Does NOT work on multiple CPU systems.
2. Does NOT work on RISC based systems
(Alpha AXP, MIPS R4x00, or PowerPCs).
b. At least a single 3.5 inch floppy disk drive:
3.5 inch, 1.44MB floppy disk drive, or a
3.5 inch Japanese 3-mode floppy disk drive.
DOES NOT SUPPORT:
- LS-120 SuperDrives (120mb / 1.44mb).
- External floppy drives (USB, serial, parallel
or other external interface).
2. OPERATING SYSTEMS:
a. Microsoft Windows 2000 (single Intel x86
(Pentium 133 MHz or higher) or fully compatible CPU).
NOTE:
In order to install or uninstall FlashPath software
on Windows 2000, you must be a user with
"Administrator Privileges".
Constructeur
Fujifilm
Catégorie
Appareils photo et vidéo numériques
Modèle
Fujifilm FD-A1-FD-A2
Description
Drivers
Système d'exploitation
Windows 95-98
Taille
1Mb
Nom de fichier
fd307958.exe
Informations
IMPORTANT NOTICE FOR THE FLOPPY DISK ADAPTER FD-A2
This file explains the FD-A2 Setup Disk V3.07 for Windows 95/98.
Please read it very carefully before you use Floppy Disk Adapter FD-A2.
(October 1999)
= = = [SYSTEM REQUIREMENTS] = = = = = =
Computer: IBM PC/AT compatible
CPU: Pentium or better
OS: Windows 95/98
Compatible SmartMedia : 5V/3.3V, 2MB to 64MB
= = = [NOTICE] = = = = = =
1) ABOUT FLOPPY DISK DRIVES (FDDS) THAT DO NOT RECOGNIZE THE FD-A2
The FD-A2 cannot be used on the following FDDs, which have
different interfaces or specifications from that of a normal 1.44MB FDD:
a) External FDD connected via PCMCIA
b) High capacity FDD such as HiFD or Super drive
c) FDD supporting 2.88MB
2) STARTUP DISK
You cannot use the FD-A2 as the Startup disk.
Use the internal hard disk, normal floppy disk, etc. as the Startup disk.
After starting up Windows 95/98, insert the FD-A2 into the FDD.
3) UPGRADING FD-A1/A1S/A1N DRIVER SOFTWARE WITH FD-A2 DRIVER SOFTWARE
When you install the driver software (Ver.3.07) on your Windows 95/98 computer
where the older driver software (Ver.1.02 , 2.01 ,2.20 or2.60) is installed,
you need to uninstall the older driver software and then install
the driver software (Ver.3.07) by referring to the FD-A2 Owner's Manual.
4) DO NOT USE DATA COMPRESSION SOFTWARE INCLUDING THE DRIVESPACE
Data compression software including the DriveSpace is not applicable to
the SmartMedia.
5) NETWORK DRIVE
The FD-A2 cannot be used across a network.
6) BRAND OF BATTERY
The battery life will vary depending on different brands.
Based on our tests, Sanyo and Maxell batteries provide the most consistent
performance with the FD-A2.
7) TERM OF VALIDITY IN BATTERY
Try to use a battery which term of validity is long.
(The Recommended operating limit is normally listed in the back
of the battery case.) A battery, which term of validity is
short may not have enough startup power due to natural discharge,
and its life can sometimes become considerably short. In extreme
cases, a read operation can be executed, while a write operation
cannot be performed.
8) BATTERY LIFE IN LOW TEMPERATURE
The FD-A2 consumes more electricity when writing than when reading,
and with 5V SmartMedia than with 3.3V SmartMedia.
Especially, in view of the battery characteristics, the battery life
shortens in low temperature.
When you are using a notebook PC with an external FDD in an environment
of low temperature such as in winter, you may not be able to write in
about 5 minutes after continuous operation.
Use the external FDD in a sufficiently warm environment.
Even when you are using the FD-A2 in an internal FDD, if the ambient
temperature is low, it is recommended for you to turn on the PC
power in advance and warm up the inside of the PC.
9) NOTICE ABOUT THE DRIVER
Do not pull out or insert the FD-A2 while format utility is being
executed. If this is done, SmartMedia may not be properly formatted.
Also, there is a chance that SmartMedia cannot be used.
Do not pull out or insert the FD-A2 while writing.
A write operation cannot be properly done. Also, there is a chance that
SmartMedia cannot be used.
When a FDD assigned to "Drive B:" is not physically
This file explains the FD-A2 Setup Disk V3.07 for Windows 95/98.
Please read it very carefully before you use Floppy Disk Adapter FD-A2.
(October 1999)
= = = [SYSTEM REQUIREMENTS] = = = = = =
Computer: IBM PC/AT compatible
CPU: Pentium or better
OS: Windows 95/98
Compatible SmartMedia : 5V/3.3V, 2MB to 64MB
= = = [NOTICE] = = = = = =
1) ABOUT FLOPPY DISK DRIVES (FDDS) THAT DO NOT RECOGNIZE THE FD-A2
The FD-A2 cannot be used on the following FDDs, which have
different interfaces or specifications from that of a normal 1.44MB FDD:
a) External FDD connected via PCMCIA
b) High capacity FDD such as HiFD or Super drive
c) FDD supporting 2.88MB
2) STARTUP DISK
You cannot use the FD-A2 as the Startup disk.
Use the internal hard disk, normal floppy disk, etc. as the Startup disk.
After starting up Windows 95/98, insert the FD-A2 into the FDD.
3) UPGRADING FD-A1/A1S/A1N DRIVER SOFTWARE WITH FD-A2 DRIVER SOFTWARE
When you install the driver software (Ver.3.07) on your Windows 95/98 computer
where the older driver software (Ver.1.02 , 2.01 ,2.20 or2.60) is installed,
you need to uninstall the older driver software and then install
the driver software (Ver.3.07) by referring to the FD-A2 Owner's Manual.
4) DO NOT USE DATA COMPRESSION SOFTWARE INCLUDING THE DRIVESPACE
Data compression software including the DriveSpace is not applicable to
the SmartMedia.
5) NETWORK DRIVE
The FD-A2 cannot be used across a network.
6) BRAND OF BATTERY
The battery life will vary depending on different brands.
Based on our tests, Sanyo and Maxell batteries provide the most consistent
performance with the FD-A2.
7) TERM OF VALIDITY IN BATTERY
Try to use a battery which term of validity is long.
(The Recommended operating limit is normally listed in the back
of the battery case.) A battery, which term of validity is
short may not have enough startup power due to natural discharge,
and its life can sometimes become considerably short. In extreme
cases, a read operation can be executed, while a write operation
cannot be performed.
8) BATTERY LIFE IN LOW TEMPERATURE
The FD-A2 consumes more electricity when writing than when reading,
and with 5V SmartMedia than with 3.3V SmartMedia.
Especially, in view of the battery characteristics, the battery life
shortens in low temperature.
When you are using a notebook PC with an external FDD in an environment
of low temperature such as in winter, you may not be able to write in
about 5 minutes after continuous operation.
Use the external FDD in a sufficiently warm environment.
Even when you are using the FD-A2 in an internal FDD, if the ambient
temperature is low, it is recommended for you to turn on the PC
power in advance and warm up the inside of the PC.
9) NOTICE ABOUT THE DRIVER
Do not pull out or insert the FD-A2 while format utility is being
executed. If this is done, SmartMedia may not be properly formatted.
Also, there is a chance that SmartMedia cannot be used.
Do not pull out or insert the FD-A2 while writing.
A write operation cannot be properly done. Also, there is a chance that
SmartMedia cannot be used.
When a FDD assigned to "Drive B:" is not physically
Constructeur
Fujifilm
Catégorie
Appareils photo et vidéo numériques
Modèle
Fujifilm FD-A1-FD-A2
Description
Drivers
Système d'exploitation
Windows NT4
Taille
888Kb
Nom de fichier
fd305nt.exe
Informations
IMPORTANT NOTICE FOR THE FLOPPY DISK ADAPTER FD-A2
This file explains the FD-A2 Setup Disk V3.05 for Windows NT4.0.
Please read it very carefully before you use Floppy Disk Adapter
FD-A2 (hereinafter FD-A2). (October 1999)
= = = [SYSTEM REQUIREMENTS] = = = = = =
Computer: IBM PC/AT compatible
(Not run on a computer with Alpha processor, e.g. Compaq AlphaServer series)
(Not run on a computer with Multi CPU system)
CPU: Pentium or better
OS: Windows NT 4.0 SP3 or SP4
Compatible SmartMedia : 5V/3.3V, 2MB to 64MB
= = = [NOTICE] = = = = = =
1) ABOUT FLOPPY DISK DRIVES (FDDS) THAT DO NOT RECOGNIZE THE FD-A2
The FD-A2 cannot be used on the following FDDs, which have
different interfaces or specifications from that of a normal 1.44MB FDD:
a) External FDD connected via PCMCIA
b) High capacity FDD such as HiFD or Super drive
c) FDD supporting 2.88MB
2) STARTUP DISK
You cannot use the FD-A2 as the Startup disk.
Use the internal hard disk, normal floppy disk, etc. as the Startup disk.
After starting up Windows NT4.0, insert the FD-A2 into the FDD.
3) INSTALL AND UNINSTALL
You will have to be logged in as a Windows NT "Administrator", or as a user
with "Administrator privileges" in order to BOTH install and uninstall
"FlashPath for Windows NT". If the user does not have administrator
privileges, installation will FAIL, with a appropriate error message
from the FlashPath instllation program.
4) DO NOT USE DATA COMPRESSION SOFTWARE INCLUDING THE DRIVESPACE
Data compression software including the DriveSpace is not applicable to
the SmartMedia.
5) NETWORK DRIVE
The FD-A2 cannot be used across a network.
6) BRAND OF BATTERY
The battery life will vary depending on different brands.
Based on our tests, Sanyo and Maxell batteries provide the most consistent
performance with the FD-A2.
7) TERM OF VALIDITY IN BATTERY
Try to use a battery which term of validity is long.
(The Recommended operating limit is normally listed in the back
of the battery case.) A battery, which term of validity is
short may not have enough startup power due to natural discharge,
and its life can sometimes become considerably short. In extreme
cases, a read operation can be executed, while a write operation
cannot be performed.
8) BATTERY LIFE IN LOW TEMPERATURE
The FD-A2 consumes more electricity when writing than when reading,
and with 5V SmartMedia than with 3.3V SmartMedia.
Especially, in view of the battery characteristics, the battery life
shortens in low temperature.
When you are using a notebook PC with an external FDD in an environment
of low temperature such as in winter, you may not be able to write in
about 5 minutes after continuous operation.
Use the external FDD in a sufficiently warm environment.
Even when you are using the FD-A2 in an internal FDD, if the ambient
temperature is low, it is recommended for you to turn on the PC
power in advance and warm up the inside of the PC.
9) NOTICE ABOUT THE DRIVER
Do not pull out or insert the FD-A2 while format utility is being
executed. If this is done, SmartMedia may not be properly formatted.
Also, there is a chance that SmartMedia cannot be used.
Do not pull out or insert the FD-A2 while writing.
This file explains the FD-A2 Setup Disk V3.05 for Windows NT4.0.
Please read it very carefully before you use Floppy Disk Adapter
FD-A2 (hereinafter FD-A2). (October 1999)
= = = [SYSTEM REQUIREMENTS] = = = = = =
Computer: IBM PC/AT compatible
(Not run on a computer with Alpha processor, e.g. Compaq AlphaServer series)
(Not run on a computer with Multi CPU system)
CPU: Pentium or better
OS: Windows NT 4.0 SP3 or SP4
Compatible SmartMedia : 5V/3.3V, 2MB to 64MB
= = = [NOTICE] = = = = = =
1) ABOUT FLOPPY DISK DRIVES (FDDS) THAT DO NOT RECOGNIZE THE FD-A2
The FD-A2 cannot be used on the following FDDs, which have
different interfaces or specifications from that of a normal 1.44MB FDD:
a) External FDD connected via PCMCIA
b) High capacity FDD such as HiFD or Super drive
c) FDD supporting 2.88MB
2) STARTUP DISK
You cannot use the FD-A2 as the Startup disk.
Use the internal hard disk, normal floppy disk, etc. as the Startup disk.
After starting up Windows NT4.0, insert the FD-A2 into the FDD.
3) INSTALL AND UNINSTALL
You will have to be logged in as a Windows NT "Administrator", or as a user
with "Administrator privileges" in order to BOTH install and uninstall
"FlashPath for Windows NT". If the user does not have administrator
privileges, installation will FAIL, with a appropriate error message
from the FlashPath instllation program.
4) DO NOT USE DATA COMPRESSION SOFTWARE INCLUDING THE DRIVESPACE
Data compression software including the DriveSpace is not applicable to
the SmartMedia.
5) NETWORK DRIVE
The FD-A2 cannot be used across a network.
6) BRAND OF BATTERY
The battery life will vary depending on different brands.
Based on our tests, Sanyo and Maxell batteries provide the most consistent
performance with the FD-A2.
7) TERM OF VALIDITY IN BATTERY
Try to use a battery which term of validity is long.
(The Recommended operating limit is normally listed in the back
of the battery case.) A battery, which term of validity is
short may not have enough startup power due to natural discharge,
and its life can sometimes become considerably short. In extreme
cases, a read operation can be executed, while a write operation
cannot be performed.
8) BATTERY LIFE IN LOW TEMPERATURE
The FD-A2 consumes more electricity when writing than when reading,
and with 5V SmartMedia than with 3.3V SmartMedia.
Especially, in view of the battery characteristics, the battery life
shortens in low temperature.
When you are using a notebook PC with an external FDD in an environment
of low temperature such as in winter, you may not be able to write in
about 5 minutes after continuous operation.
Use the external FDD in a sufficiently warm environment.
Even when you are using the FD-A2 in an internal FDD, if the ambient
temperature is low, it is recommended for you to turn on the PC
power in advance and warm up the inside of the PC.
9) NOTICE ABOUT THE DRIVER
Do not pull out or insert the FD-A2 while format utility is being
executed. If this is done, SmartMedia may not be properly formatted.
Also, there is a chance that SmartMedia cannot be used.
Do not pull out or insert the FD-A2 while writing.
