Aten PN9108 Download Drivers, Manual and Firmware

Improved communication between PN9108 and modem

1. About Power Monitor
Power Monitor is a utility, which is used to monitoring power status (UPS signal). When UPS signals (Power Fail and Low
battery) are detected, this utility will shutdown Windows system safely.
This version of software is for ALTUSEN Power over the NET product.
2. Using Power Monitor
a). Install Power Monitor by executing self-extract setup program (PMonitorSetup -ALTUSEN-V1.1.101 .exe). Install
program will set Power Monitor to Windows startup folder to let system launch it automatically when system starts.
b). Power Monitor could be launched by system automatically, or by double-click shortcut icon on desktop manually too.
c). The polarity of UPS signals (both Power Fail and Low Battery) that is monitored are Positive only.
d). Default COM port for Power Monitor is COM1.
e). After Power Monitor was launched, it starts monitoring power status (via COM1) automatically. If COM1 port was
occupied by other utility, it could not start monitoring, and the dialog below will be displayed.
f). If you are using other COM port, please choose it from Option dialog.
g). If monitoring is started, monitoring icon will be displayed at task bar (right-bottom), if monitoring is stopped, nonmonitoring
icon will be displayed at task bar.
h). If the utility has already launched, and user try to execute utility again, the error dialog below will be displayed.
Monitoring icon:
Non-monitoring icon:
i). When monitoring was stopped, user can set option by double-click left button on non-monitoring icon at task bar, or
click right button on non-monitoring icon at task bar, then select “Option…” from menu. The dialog below will be
displayed. What user can set in option dialog is COM port only.
j). User can click right button on power monitor icon at task bar to choose starting or stopping monitoring.
k). When Power Monitor detected UPS signal (Power Fail and Low battery), a dialog box below will be displayed and the
utility will start system shutdown process in 5 seconds
l). About dialog
m). User can uninstall the utility by choose uninstall from Windows start menu (Start \ Program \ ATEN Power Monitor Uninstall Power Monitor) or form “Control Panel \ Add/Remove Program” in Windows, utility name is “ATEN Power
Monitor”.

About the IP Installer
The IP Installer utility provides a simple method to configure IP related
settings. The following ALTUSEN products are supported by this version:
PN9108, SN0108, SN0116, and KM0832.
IP Installer Operation
When you execute the IP Installer program (IPInstaller.exe), the main screen
appears:
IP Installer
2
The Device List:
When the IP Installer main window comes up, the utility scans the network for
devices and lists the ones it finds in the device list panel. The device list panel
consists of three columns, as shown in the following table:
Clicking Enumerate causes the utility to send an Enumerate command and
wait for replies from the devices. It then refreshes the list based on the
response it receives.
Network Adapter:
The Network Adapter selection box, located just below the Device List,
pertains to computers that have more than one network adapter installed. Users
can use this to select the adapter that they want Enumerate to be directed to.

1. About IP Installer
This utility provides a simple method to configure IP related setting. It is designed for ATEN’s over the NET product that
supports related protocol.
This version of software is for ALTUSEN over the NET product (PN9108, SN0108, and SN0116)
2. Using IP Installer
a). Main window
Execute “IPInstaller.exe”, the main window below will be displayed.
b). There are 3 column in Device List
Model Name: device model name such as PN9108, SN0116, etc.
MAC Address: device MAC address
IP Address: current IP address for this device
c). Enumerate button
Click this button, the utility will send enumerate command and receive reply from device(s), then refresh the Device List.
d). Obtain an IP method
There are two methods to obtain IP in device.
Use dynamic IP: select “Obtain as IP address automatically (DHCP)”
Use static IP: select “Specify an IP address”, then change IP Address, Subnet Mask, and Gateway
e). Set IP
Select obtaining IP method, change/fill related field, then click “Set IP” button.
The main window will be freeze until IP setting has finished completely.