Citizen CMP-10 Download Drivers
Available 4 files for CMP-10
Company
Citizen
Categories
Printers
Model
Citizen CMP-10
Description
Drivers
Operating Systems
CMP10 LOAD
Size Driver
214Kb
File Name
cmp10load.exe
Info
This software is for loading firmwae to CMP-10 through serial connector.
Company
Citizen
Categories
Printers
Model
Citizen CMP-10
Description
Drivers
Operating Systems
CMP10 Setup Tool
Size Driver
104Kb
File Name
cmp10setuptool.exe
Company
Citizen
Categories
Printers
Model
Citizen CMP-10
Description
Drivers
Operating Systems
Explanation for CMP10 LOAD
Size Driver
6Kb
File Name
cmp10load.pdf
Info
Instruction to load CMP-10 firmware
Following items are required
CMP-10 with the paper roll in it with enough battery level
Serial cable
PC with Windows + Serial port
CMP10LOAD.EXE
Firmware data
CMP-10 side
Connect Serial cable to CMP-10 and PC
Turn CMP-10 while pressing LF switch and hold the LF switch for more than 6 second.
Then CMP-10 print “Flash Programing mode” after buzzer sounds.
PC side
Run CMP10LOAD.EXE
If you do not use COM1, please change the COM port.
Check “FIRMWARE”.
Press BROWSE and choose Firmware data file.
When all of above are done, please press START.
Firmware loading will be finished in about 30 seconds.
Never turn the CMP-10 off during loading firmware.
After finishing firmware loading, please check firmware version by self test.
Following items are required
CMP-10 with the paper roll in it with enough battery level
Serial cable
PC with Windows + Serial port
CMP10LOAD.EXE
Firmware data
CMP-10 side
Connect Serial cable to CMP-10 and PC
Turn CMP-10 while pressing LF switch and hold the LF switch for more than 6 second.
Then CMP-10 print “Flash Programing mode” after buzzer sounds.
PC side
Run CMP10LOAD.EXE
If you do not use COM1, please change the COM port.
Check “FIRMWARE”.
Press BROWSE and choose Firmware data file.
When all of above are done, please press START.
Firmware loading will be finished in about 30 seconds.
Never turn the CMP-10 off during loading firmware.
After finishing firmware loading, please check firmware version by self test.
Company
Citizen
Categories
Printers
Model
Citizen CMP-10
Description
Drivers
Operating Systems
Explanation for CMP10 Setup Tool
Size Driver
160Kb
File Name
cmp10setuptool.pdf
Info
This software is for configure CMP-10 through serial connector. Explanation of CMP-10 Setup Tool
1. Preparation
Please connect CMP-10 to PC by serial cable.
Please make sure which serial port is used for the serial cable.
Please check baud rate of CMP-10 by self-test.
2. Explanation of screen
When CMP-10 Setup Tool starts, following window will show up.
Please set “Port” and “Speed” for the serial port number and baud rate
And please press [Connect & Get].
Then current setting is loaded from CMP-10 the screen and window is changed like below.
Make necessary change here and press [Connect ?? Set]. Then changed values are set on
* “Printer Info/Support” shows current setting values and supported function.
User cannot change these values.
* Right half is user changeable values.
* “Selectable Parameters” is memory switches. By selecting/deselecting items, function is
changed.
* “Density” is darkness of printed results.
* ”Auto off time” is to set the auto power off time.
* By selecting “Enable Black Mark Mode”, black mark function becomes enabled.
* “IrDA max speed” is the maximum data transmission speed by IrDA. There is some chance
to miss print data with 115200. So usually it is recommended to set for 57600.
* On “IrDA protocol”, if “Raw” is selected, CMP-10 does not use IrDA protocol. This may be
convenient for special infrared communication.
3. Explanation of menu
On the “Advanced” menu, you can easily use function of CMP-10 or change CMP-10 setting.
1. Preparation
Please connect CMP-10 to PC by serial cable.
Please make sure which serial port is used for the serial cable.
Please check baud rate of CMP-10 by self-test.
2. Explanation of screen
When CMP-10 Setup Tool starts, following window will show up.
Please set “Port” and “Speed” for the serial port number and baud rate
And please press [Connect & Get].
Then current setting is loaded from CMP-10 the screen and window is changed like below.
Make necessary change here and press [Connect ?? Set]. Then changed values are set on
* “Printer Info/Support” shows current setting values and supported function.
User cannot change these values.
* Right half is user changeable values.
* “Selectable Parameters” is memory switches. By selecting/deselecting items, function is
changed.
* “Density” is darkness of printed results.
* ”Auto off time” is to set the auto power off time.
* By selecting “Enable Black Mark Mode”, black mark function becomes enabled.
* “IrDA max speed” is the maximum data transmission speed by IrDA. There is some chance
to miss print data with 115200. So usually it is recommended to set for 57600.
* On “IrDA protocol”, if “Raw” is selected, CMP-10 does not use IrDA protocol. This may be
convenient for special infrared communication.
3. Explanation of menu
On the “Advanced” menu, you can easily use function of CMP-10 or change CMP-10 setting.
