Epson Stylus Pro 4000 Professional Edition Download Manual

Load Roll Paper
1 Slide the black paper stop off the end of the spindle.
2 If the paper has a 2-inch core, remove the adaptersby pressing the four tabs.
Note: Make sure your hands are clean, and avoid touching the printable surface of the paper.
Try to handle paper by the edges. Make sure you donít rub or scratch the coating or dent theedges of the paper.
3 Position the roll so the paper unwinds as shown,then slide it onto the spindle.
4 Slide the black paper stop back onto the spindle.
Insert it firmly into the end of the roll.
5 Open the roll paper cover.
6 Place the paper and spindle in the printer asshown, with the gray end on the right.
7 Make sure the printer is powered on andready. Press the Paper Source button untilthe or roll paper icon appears.
8 Release the paper lever.
9 Hold both sides of the paper and feed it into the slot until the paperis aligned with the OTHER mark and the vertical line on the paper tray cover. Then move the paper lever to the secured position.
10 Raise the roll paper support on top of thepaper tray. Then close the roll paper cover.
EPSON Stylus

Pro 4000
Unpack
1 Make sure you have all the parts shown below for your EPSON Stylus Pro 4000:Warning: The printer weighs about 85 pounds, and should be lifted by two people.
2 Remove all the packing materials andtape. Save the box and packaging in caseyou need to ship the printer.
3 Loosen the two screws and remove thecarriage retainer bracket.
4 Unlock the print head carriage bypulling the green tab to the left. Donot remove the tab.
Note: To lock the print head carriagefor transportation, push the green tab tothe right.
Set Up and Plug In
1 Connect the power cord to the AC inlet on the back of the printer.
2 Plug the other end of the power cord into a properly grounded electrical outlet.
3 Attach the exhaust port cover by sliding italong the slots on the back of the printer.
4 Insert the paper tray into the slots atthe front of the printer.
Paper tray
Printer
Ink cartridges
Power cord
Roll paper spindle Spindle adapters
(attached to spindle)
Start Here
Start Here
Power button
AC inlet
Paper
Sourcebutton
Roll paper cover
Exhaust port coververtical line
OTHER mark
CPD17011R1_Isa_SH_E.qxd 9/21/04 5:13 PM Page 1Load Roll Paper
1 Slide the black paper stop off the end of the spindle.
2 If the paper has a 2-inch core, remove the adaptersby pressing the four tabs.
Note: Make sure your hands are clean, and avoid touching the printable surface of the paper.
Try to handle paper by the edges. Make sure you donít rub or scratch the coating or dent theedges of the paper.
3 Position the roll so the paper unwinds as shown,then slide it onto the spindle.
4 Slide the black paper stop back onto the spindle.
Insert it firmly into the end of the roll.
5 Open the roll paper cover.
6 Place the paper and spindle in the printer asshown, with the gray end on the right.
7 Make sure the printer is powered on andready. Press the Paper Source button untilthe or roll paper icon appears.
8 Release the paper lever.
9 Hold both sides of the paper and feed it into the slot until the paperis aligned with the OTHER mark and the vertical line on the paper tray cover. Then move the paper lever to the secured position.
10 Raise the roll paper support on top of thepaper tray. Then close the roll paper cover.
EPSON Stylus

Pro 4000
Unpack
1 Make sure you have all the parts shown below for your EPSON Stylus Pro 4000:Warning: The printer weighs about 85 pounds, and should be lifted by two people.
2 Remove all the packing materials andtape. Save the box and packaging in caseyou need to ship the printer.
3 Loosen the two screws and remove thecarriage retainer bracket.
4 Unlock the print head carriage bypulling the green tab to the left. Donot remove the tab.
Note: To lock the print head carriagefor transportation, push the green tab tothe right.
Set Up and Plug In
1 Connect the power cord to the AC inlet on the back of the printer.
2 Plug the other end of the power cord into a properly grounded electrical outlet.
3 Attach the exhaust port cover by sliding italong the slots on the back of the printer.
4 Insert the paper tray into the slots atthe front of the printer.
Install Ink
Use the ink cartridges that came with your printer for initial ink charging. During the initialinstallation process, it is normal for up to one-third of the ink in each cartridge to be used.
1 Press the Power button to turn on the printer.
2 Press both ink compartment covers to open them.
3 Raise both ink levers.
4 Remove each ink cartridge from its package andgently shake the cartridge.
5 Install the ink cartridges in the printer. Holdeach cartridge with the arrow pointing towardthe printer, then insert it into its slot. Make sureyou insert each cartridge in the correct slot.
6 After installing all 8 cartridges, lower the ink levers.
The printer begins charging the ink delivery systemand the Pause light flashes.
7 After approximately 2 minutes, ink lever messagesappear on the LCD. follow the instruction to raiseor lower the ink levers.
Caution: Charging takes about 8 minutes. Never turn off the printer,release the paper lever, or open the cover while the Pause light is flashing,or you may damage the printer.
8 When READY appears on the LCD display, charging is complete. Close the ink compartment covers.
Caution: Always turn off the printer using the Power button. Then wait untilthe LCD display turns off. This ensures that the print head is safely capped.
Paper tray
Printer
Ink cartridges
Power cord
Roll paper spindle Spindle adapters
(attached to spindle)
Start Here
Start Here
Power button
AC inlet
Paper
Sourcebutton
Roll paper cover
Exhaust port coververtical line
OTHER mark
CPD17011R1_Isa_SH_E.qxd 9/21/04 5:13 PM Page 1Load Roll Paper
1 Slide the black paper stop off the end of the spindle.
2 If the paper has a 2-inch core, remove the adaptersby pressing the four tabs.
Note: Make sure your hands are clean, and avoid touching the printable surface of the paper.
Try to handle paper by the edges. Make sure you donít rub or scratch the coating or dent theedges of the paper.
3 Position the roll so the paper unwinds as shown,then slide it onto the spindle.
4 Slide the black paper stop back onto the spindle.
Insert it firmly into the end of the roll.
5 Open the roll paper cover.
6 Place the paper and spindle in the printer asshown, with the gray end on the right.
7 Make sure the printer is powered on andready. Press the Paper Source button untilthe or roll paper icon appears.
8 Release the paper lever.
9 Hold both sides of the paper and feed it into the slot until the paperis aligned with the OTHER mark and the vertical line on the paper tray cover. Then move the paper lever to the secured position.
10 Raise the roll paper support on top of thepaper tray. Then close the roll paper cover.
Paper
Sourcebutton
Roll paper coververtical line
OTHER markLoad Cut Sheet Paper
When you are ready to print on cut sheet paper, make sure you release the paper lever and wind up the roll paper. Then return the paper lever to the secured position and close the rollpaper cover.
Note: Some papers cannot be used with the paper tray. You need to load them through the front or topmanual feed slots. See the Printer Guide for details.
1 Make sure the printer is on and readyto print.
2 Pull out the paper tray and cover,then remove the cover. Flip up thepaper guide roller.
3 Slide the edge guide all the way to the left.
4 Thumb through a stack of paper, then gently tapit on a flat surface to even the edges.
5 Load the sheets in the portraitorientation, with the whiter or glossierprintable side face down. Place the paperall the way back, against the right side ofthe tray.
Donít load paper above the arrow markinside the edge guide.
6 Adjust the paper tray and edge guideaccording to the paper size. For smallsheets, raise the paper guide and moveit to the edge of the stack.
7 Flip down the paper guide roller, thenreplace the paper tray cover and adjustits length.
Note: Make sure the roll paper supportis not raised.
8 Press the Paper Source button until you see the cut sheet icon.
Paper guideroller
CPD17011R1_Isa_SH_E.qxd 9/21/04 5:13 PM Page 2Connect to Your System
You can use either of the following connections. Make sure your system has the appropriateport, and you have a standard, shielded cable 10 feet long or less:If you have the optional EpsonNet Ethernet card,you can connect the printer directly to yournetwork. Youíll need a standard RJ-45 networkcable.
1 Make sure that both the printer and thecomputer are off.
2 Plug the interface cable into theappropriate port on the printer.
3 Plug the other end of the cable into the appropriate connector on yourcomputer or network hub.
Install the Software
Follow the steps below for Macintosh
or Windows.

Macintosh
1 Turn on your Macintosh and your printer.
2 Insert the printer software CD-ROM. If necessary, double-click the EPSON
CD-ROM to open its window.
3 Double-click the EPSON OS X Installer.
If you are using Mac

OS 9, double-click the EPSON OS 9 Installer.
4 Double-click Install Reference
Guide and wait while the guideis installed.
5 Double-click Install Printer Driverand Utilities. Enter your passwordif necessary.
6 Follow the on-screen instructions toinstall your software. When you see amessage informing you that installationwas successful, click Restart to restartyour Macintosh.
7 If youíre using OS X, continue with step 8.
If youíre using OS 9, open the
Chooser from the Apple
menu.
Select SPro 4000, then select yourport and turn on background printing.
Your installation is complete.
8 Open the Applications folder, thenopen the Utilities folder and open the
Print Center or Printer Setup utility.
9 Click the Add icon at the top of the Printer List window.
USB cable
IEEE FireWire
cable
IEEE FireWire connector
USB connector
CPD17011R1_Isa_SH_E.qxd 9/21/04 5:13 PM Page 2
Continue
10 Pull down the menu and select the connection you are usingóeither EPSON USB, EPSON FireWire, or EPSON TCP/IP. The Stylus Pro 4000 appears on the Printer List screen. 11 Click Stylus Pro 4000, then open the Page Setup pull-down menu. 12 Select All, then click Add. Windows 1 Make sure your printer is turned off. 2 Turn on your computer. 3 Insert the printer software CD-ROM in your computer. The installer starts automatically. If it doesnít start, double-click My Computer or click Start > My Computer. Then double-click your CD-ROM icon. 4 Double-click Install Printer Driver and Utilities. 5 When you see a window asking you to turn on your printer, press the Power button. 6 When you see a message that setup is complete, click OK. 7 Double-click Install Reference Guide and wait while the guide is installed. 8 If you need the ZEHPlot or EPSON HDI driver, double-click the icon and follow the instructions on the screen. 9 Click to close the installer, then remove the CD-ROM. Any Questions? Hereís where to look for answers: Mastering Your Printer Video Workshop Insert the Mastering Your Printer CD-ROM and select the video you want to watch. Youíll get expert advice on optimizing print quality, printing from Photoshop, and basic printer operations. Printer Guide Refer to this book for complete instructions on using and maintaining your printer, as well as problem-solving tips and specifications. Quick Reference Guide Keep this booklet handy for instructions on loading paper, replacing ink cartridges and other components, changing and aligning the print head, and what to do when you see a printer error message. Electronic Reference Guide Double-click the SP4000 Reference Guide icon on your desktop. If you didnít install the guide, insert the printer software CD-ROM in your CD-ROM or DVD drive. Then double-click Install Reference Guide. EPSON Technical Support ē World Wide Web http://support.epson.com ē Call (888) 377-6611. Make sure you have your EPSON Preferred SM Unit ID number. If you have any difficulty with this service, call (562) 276-1305. EPSON and EPSON Stylus are registered trademarks of SEIKO EPSON CORPORATION. EPSON Preferred is a service mark of Epson America, Inc. General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. EPSON disclaims any and all rights in those marks. Printed on recycled paper 2004 by Epson America, Inc. 9/04 Printed in USA CPD-17011R1 CPD17011R1_Isa_SH_E.qxd 9/21/04 5:13 PM Page 2 Continue

TXT / PDF

Available 44 files for Stylus Pro 4000 Professional Edition View all >
HelpDrivers Since March 2000